Coal tar pitch (CTP), a by-product of coking industry, has a unique molecule structure comprising an aromatic nucleus and several side chains bonding on this graphene-like nucleus, which is very similar to the structure of graphene quantum dots (GQDs). Based on this perception, we develop a facile approach to convert CTP to GQDs only by oxidation with hydrogen peroxide under mild conditions. One to three graphene layers, monodisperse GQDs with a narrow size distribution of 1.7 ± 0.4 nm, are obtained at high yield (more than 80 wt. %) from CTP. The as-produced GQDs are highly soluble and strongly fluorescent in aqueous solution. This simple strategy provides a feasible route towards the commercial synthesis of GQDs for its cheap material source, green reagent, mild condition, and high yield.
The conventional synthesis route of graphene oxide (GOG), based on Hummers method, suffers from explosion risk, environmental concerns and a tedious synthesis process, which increases production costs and hinders its practical applications. Herein, we report a novel strategy for preparing few-layer graphene oxide (GOH) from humic acid via simple hydrothermal treatment. The formation of GOH is mainly attributed to the hydrolysis, oxidation and aromatization of humic acid under hydrothermal conditions. The as-prepared few-layer GOH has typical morphology (thin and crumpled sheets with the thickness of ~3.2 nm), crystal structure (a Raman ID/IG ratio of 1.09) and chemical composition (an X-ray Photoelectron Spectroscopy (XPS) O/C atomic ratio of 0.36) of few-layer GOG. The thermally reduced GOH (r-GOH) delivers considerable area capacitance of 28 µF·cm−2, high rate capability and low electrochemical resistance as supercapacitor electrodes. The described hydrothermal process shows great promise for the cheap, green and efficient synthesis of few-layer graphene oxide for advanced applications.
Developing effective methods for the instant detection of Cu2+ and S2− is highly desired in the biological and environmental fields. Herein, a novel fluorescent nanoprobe was elaborately designed and synthesized by grafting a phenanthroline derivative onto the surface of carbon dots (CDs). The obtained functionalized CDs (FCDs) exhibited blue fluorescence (FL) with excellent photostability and possessed a mean diameter around 4 nm. Cu2+ can be selectively captured by the phenanthroline group of FCDs to generate an absorptive complex in situ, leading to obvious quenching of the FCDs’ FL signal through an inner filter effect. Furthermore, the FL of the FCD–Cu2+ can be effectively recovered by S2− anions due to the release of FCDs from the FCD–Cu2+ complex owing to the formation of stable CuS (Ksp = 1.27 × 10−36) between S2− and Cu2+. The detection limits of the FCDs were determined to be 40.1 nM and 88.9 nM for Cu2+ and S2−, respectively. Moreover, this nanoprobe can also be used for the imaging of intracellular Cu2+ and S2−, which shows strong application prospects in the field of biology.
In this work, graphitic carbon nitride nanosheets decorated like nickel oxide microspheres (NiO/g‐C 3 N 4 , Ni/CN) were successfully synthesised by a simple hydrothermal method. The morphologies of the as‐prepared samples were analysed by scanning electron microscopy and the diameter of the microspheres was found to be about 2.5 μm. At an optimum working temperature of 240°C, the response to 500 ppm CO is 2.729 for the Ni/CN‐10 (10 wt% g‐C 3 N 4 modified NiO) sensor, which is much higher than those of the NiO sensor (1.408). Besides the higher response, the Ni/CN sensors also showed good repeatability and stability for CO detection. Excellent gas sensitivity properties can be attributed to the p–n heterojunction formed at the interface, which can provide more potential active sites for surface reactions. In addition, the sensitisation of g‐C 3 N 4 also plays an important role in the improvement of CO‐sensing performance.