This paper presents a new vehicle classification and develops a traffic monitoring detector to provide reliable vehicle classification to aid traffic management systems. The basic principle of this approach is based on measuring the dynamic strain caused by vehicles across pavement to obtain the corresponding vehicle parameters – wheelbase and number of axles – to then accurately classify the vehicle. A system prototype with five embedded strain sensors was developed to validate the accuracy and effectiveness of the classification method. According to the special arrangement of the sensors and the different time a vehicle arrived at the sensors one can estimate the vehicle’s speed accurately, corresponding to the estimated vehicle wheelbase and number of axles. Because of measurement errors and vehicle characteristics, there is a lot of overlap between vehicle wheelbase patterns. Therefore, directly setting up a fixed threshold for vehicle classification often leads to low-accuracy results. Using the machine learning pattern recognition method to deal with this problem is believed as one of the most effective tools. In this study, support vector machines (SVMs) were used to integrate the classification features extracted from the strain sensors to automatically classify vehicles into five types, ranging from small vehicles to combination trucks, along the lines of the Federal Highway Administration vehicle classification guide. Test bench and field experiments will be introduced in this paper. Two support vector machines classification algorithms (one-against-all, one-against-one) are used to classify single sensor data and multiple sensor combination data. Comparison of the two classification method results shows that the classification accuracy is very close using single data or multiple data. Our results indicate that using multiclass SVM-based fusion multiple sensor data significantly improves the results of a single sensor data, which is trained on the whole multisensor data set.
31 October 2008 in Electrochemistry Communications
At present, the detection technology of non-contact ultrasonic and transient earth voltage is widely used in the partial discharge detection of switchgear. The test result is directly related to the diagnosis and evaluation of the insulation state of electrical equipment. In order to characterize the accuracy of PD detection, it is proposed to use the terminal linearity calculation to analyze the linearity of the PD detector in the frequency band. Finally, the linearity test of the UltraTEV Plus PD detector is carried out by setting up a dedicated performance test platform in the laboratory, which verifies the effectiveness of the method and reflects the minimum linearity near the resonant frequency.
In this paper, four low-melting alloy materials, Sn-3.5Ag, Sn-1.6Cu, Sn-Zn-0.7Cu and Sn-8Zn-3Bi, were used to study the wettability of these materials on copper substrates. Using the Image Pro Plus software to calculate the spread area and analyze the spread-ability of low-melting alloy materials with different compositions on the copper substrate. The calculation results show that the low-melting alloy material with strong spreading property is Sn-1.6Cu. The interface morphology of Sn-1.6Cu on the copper substrate after wetting equilibrium was observed by SEM and EDX instruments. The interface quality was judged according to the interface morphology, and the interface element distribution and element penetration were analyzed. The experimental results show that the interface between Sn-1.6Cu and the copper substrate is reliable, and there are no interface defects such as porosity, slag inclusion and crack. The research work in this paper provides a theoretical basis for the subsequent material improvement research.
This paper presents an equivalent circuit model of photovoltaic cells, and then discusses the photovoltaic (PV) grid power generation system in the maximum power point tracking (MPPT) control principle of the boost circuit. The MATLAB/Simulink software was used to model and simulate MPPT verification of the system. The simulation results showed the effectiveness of the control Strategy. As a conclusion, potential solution to MPPT The BOOST circuit adopts the MPPT control in photovoltaic power generation system, not only can improve the efficiency of photovoltaic cells, and thus improve the efficiency of the photovoltaic power generation systems.
This paper presents two kinds of direct methanol fuel cell (μDMFC) stack in planar array. The silicon-based DMFC stack is designed in a flip-flop configuration using MEMS technology, and the stainless steel stack is fabricated using stamping technology. Compared to stainless steel stack, the flip-flop silicon-based stack may reduce the connection space and lower the contact resistance between the membrane electrode assembly and the plates. Experimental results show that these two kinds of stacks have similar output 6.75mW and 6.77mW at same operation conditions. The performance of the MEMS-based DMFC stack is rather good for application in portable electronic products