Impulse radio ultrawideband ranging has recently received significant attention due to the high accuracy it can achieve. Although most research efforts have focused on ranging in indoor and outdoor environments, other environments such as harsh industrial environments introduce unique challenges. This paper discusses the impact of propagation characteristics of harsh industrial environments on ranging accuracy, and also discusses principles and challenges of non-line-of-sight identification in industrial scenarios. To illustrate these challenges, a measurement campaign using 802.15.4a radios was conducted in a Heavy Machines Laboratory. The results show that the non-line-of-sight condition can be accurately identified if adequate models for such an environment are used.
29 January 2020 in IEEE Transactions on Industrial Informatics
Accurate ranging and localization in non-line-ofsight (NLOS) conditions is an open research problem. In indoor environments, NLOS causes ranging and location errors due to reflections, refraction and other propagation phenomena. This paper proposes a method to mitigate ranging errors caused by through-the-wall (TTW) NLOS conditions. We develop a TTW ranging model that has less parameters than the conventional ranging model found in literature, and evaluate it using measurements from ultra-wideband radios. The developed ranging model expresses the difference between NLOS and LOS ranges, i.e. bias, in terms of walls' relative permittivity and thickness. NLOS ranges expressed with the proposed TTW ranging model are used as input to a trilateration algorithm. The proposed method is evaluated via simulations and it is shown that localization using the simplified ranging model as input to the trilateration algorithm effectively mitigates NLOS ranging errors, resulting in location estimates that are close to LOS location estimates.
One hurdle to accurate indoor localization using time-based networks is the presence of Non-Line-Of-Sight (NLOS) and multipath signals, affecting the accuracy of ranging in indoor environments. NLOS identification and mitigation have been studied over the years and applied to different time-based networks, with most works considering NLOS links with WiFi and UWB channels. In this article, we discuss the effects and challenges of NLOS conditions on indoor localization and present current state-of-the-art approaches to NLOS identification and mitigation in literature. We survey these approaches and classify them under different categories together with their merits and demerits. We further categorize approaches to tackle NLOS effects into single and hybrid measurement-based approaches in this work. Lessons learnt from the survey with future directions are also presented in this article.
Search and rescue missions still typically rely on teams of people tirelessly searching for victims. Advances in technology have seen the use of drones to help the rescuers in their search. These drones primarily use visual systems but cost and visibility are major drawbacks with those systems. The system described in this paper attempts to resolve the localisation problem for drones used in search and rescue operations by making use of acoustic source localisation. The source location is estimated in terms of an azimuth estimation (the bearings or angle towards the source) as well as the distance. The proposed system showed promising results for both the azimuth and distance estimations.
15 November 2023 in IEEE Transactions on Industrial Informatics
Positioning with ultrawideband (UWB) is prominent among industrial localization systems, due to its high-range resolution attributes and lower cost. However, one notable challenge with UWB positioning in industrial environments is the prevalent presence of nonline-of-sight (NLOS) components or signals that degrade localization performance drastically. Coupled with this, industrial settings tend to constantly change making NLOS signals challenging to characterize each time these changes occur. Recently, promising approaches have been proposed to identify NLOS components, however their performances are limited to the specific environment where measurements were performed. Their performance cannot be extended to other unknown environments due to the distribution divergence problem, owing to differences in environments captured by the channel impulse response (CIR) waveforms. This therefore requires laborious processes of data collection and training environment-specific models for NLOS identification. In this article, we propose a robust transfer learning-based NLOS identification approach, which harnesses transition information via cross-domain mappings from both source and target domains, to construct representative homogeneous features of both domains. The representative homogeneous features capture discriminative information of both domains, while reducing the distribution divergence between the domains, making it easy to classify LOS and NLOS components from both environments together. To test the robustness of our approach, we perform extensive simulations with CIR data collected from two distinct environments—“hard NLOS” (characterized by high relative permittivity of surrounding objects, e.g., thick concrete walls, metallic objects, etc.) and “soft NLOS” (characterized by low relative permittivity of surrounding objects, e.g., plasterboard walls). Our proposed approach is not just effective in transferring knowledge between distinct environments, but significantly outperforms state-of-the-art works to NLOS identification in UWB positioning networks, while reducing the laborious process of data collection in the target domain.
3 February 2021 in IEEE Industrial Electronics Magazine