Anastasia Denissova

Anastasia Denissova


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 November 2024 in Symmetry
Verified
Journal Article
Open access
PDF file
AVAndrey Volokitin
Andrey Volokitin
IVIrina Volokitina
Irina Volokitina
MSM. Seref Sonmez
M. Seref Sonmez
ADAnastasia Denissova
Anastasia Denissova
ZGZoya Gelmanova
Zoya Gelmanova
Traditionally, structural wire is characterized by a homogeneous microstructure, where the average grain size in different parts of the wire is uniform. According to the classical Hall–Petch relationship, a homogeneous polycrystalline metal can be strengthened by decreasing the average grain size since an increase in the volume fraction of grain boundaries will further impede the motion of dislocations. However, a decrease in the grain size inevitably leads to a decrease in the ductility and deformability of the material due to limited dislocation mobility. Putting a gradient microstructure into the wire has promising potential for overcoming the compromise between strength and ductility. This is proposed a new combined technology in this paper in order to obtain a gradient microstructure. This technology consists of deforming the wire in a rotating equal-channel step die and subsequent traditional drawing. Deformation of copper wire with a diameter of 6.5 mm to a diameter of 5.0 mm was carried out in three passes at room temperature. As a result of such processing, a gradient microstructure with a surface nanostructured layer (grain size ~400 nm) with a gradual increase in grain size towards the center of the wire was obtained. As a result, the microhardness in the surface zone was 1150 MPa, 770 Mpa in the neutral zone, and 685 MPa in the central zone of the wire. Such a symmetrical spread of microhardness, observed over the entire cross-section of the rod, is a direct confirmation of the presence of a gradient microstructure in deformed materials. The strength characteristics of the wire were doubled: the tensile strength increased from 335 MPa to 675 MPa, and the yield strength from 230 MPa to 445 MPa. At the same time, the relative elongation decreased from 20% to 16%, and the relative contraction from 28% to 23%. Despite the fact that the ductility of copper is decreased after cyclic deformation, its values remain at a fairly high level. The validity of all results is confirmed by numerous experiments using a complex of traditional and modern research methods, which include optical, scanning, and transmission microscopy; determination of mechanical properties under tension; and measurement of hardness and electrical resistance. These methods allow reliable interpretation of the fine microstructure of the wire and provide information on its strength, plastic, and electrical properties.

8 October 2026 in Scientific Reports
Verified
Journal Article
Open access
PDF file
IVIrina Volokitina
Irina Volokitina
Andrey VolokitinAndrey Volokitin
Andrey Volokitin
ADAnastasia Denissova
Anastasia Denissova
ZGZoya Gelmanova
Zoya Gelmanova
GUGulnara Ulyeva
Gulnara Ulyeva
This study addresses the challenge of optimizing the trade-off between strength, ductility, and electrical conductivity in high-strength microcomposite Cu-14Fe alloy wires. A novel thermo-mechanical processing approach is proposed, combining successive cycles of twisting in an equal-channel step die with subsequent drawing along two temperature routes: cold (Route A, room temperature) and warm (Route B, 250 °C), followed by low-temperature annealing (300–500 °C). Results demonstrate that cold processing induces a sharp gradient microstructure (from submicron grains ~ 400 nm at the surface to 7 μm in the center), yielding maximum hardening. Conversely, warm deformation activates dynamic recovery, forming a uniform polygonized structure that preserves ductility. It was found that deformation processing along Route A ensures maximum workpiece hardening (ultimate strength σ в = 675 MPa), while warm deformation along Route B allows for the retention of an increased ductility resource δ = 19.0%, ψ = 25.0%. An anomalous change in mechanical properties was revealed during subsequent thermal treatment: annealing at 400 °C initiates a simultaneous increase in strength and ductility for both routes, achieving peak σ в values of 700 MPa (Route A) and 610 MPa (Route B). A key finding is an anomalous simultaneous increase in both strength and ductility during post-deformation annealing at 400 °C for both routes, driven by precipitation hardening from the decomposition of the supersaturated solid solution. Ultimately, preliminary warm deformation (Route B) proves technologically superior, establishing a thermally stable subgrain structure with enhanced resistance to softening and restrained recrystallization kinetics across the investigated temperature range.