Ramesh K Donga

Dr. Ramesh K Donga


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

6 July 2025 in Scientific Reports
Verified
Journal Article
Open access
PDF file
RDRamesh K Donga
Ramesh K Donga
SKSuresh Kumar
Suresh Kumar
GVGurunadh Velidi
Gurunadh Velidi
This study presents an investigation into enhancing heat transfer in parabolic trough collectors (PTCs). The research focuses on improving convective heat transfer by incorporating longitudinal fins within the tubular absorber of a PTC. The study examines a PTC (parabolic trough collector) system with the following specifications: a 1.84 m focal length, a 5 m aperture width, and an absorber measuring 70 mm in outer diameter. The variable solar flux on the absorber is determined using SolTrace software. The receiver was simulated using the finite volume method. The heat flux derived from SolTrace simulations serves as a boundary condition. A comparative analysis is conducted between the findings from a parametric investigation on a standard receiver and those equipped with finned tubular absorbers. This comparison spans Reynolds numbers from 0.25 × 105 to 2.82 × 105. Studies have demonstrated that absorbers with fins substantially improve heat transfer. The tubular absorber equipped with fins shows a significant rise of 40.1% in the Nusselt number. Its performance evaluation criteria reach a peak of 1.28 when the Reynolds number is 2.82 × 105.

30 December 2024 in Scientific Reports
Verified
Journal Article
Open access
PDF file
RDRamesh K Donga
Ramesh K Donga
SKSuresh Kumar
Suresh Kumar
GVGurunadh Velidi
Gurunadh Velidi
This numerical investigation examines the performance and exergy analysis of parabolic trough solar collectors, focusing on the substitution of the conventional circular absorber with a rhombus-shaped absorber. By evaluating the thermal and fluid dynamics properties, this study aims to identify improvements in overall system performance and efficiency. This numerical study conducts a comprehensive thermal analysis of parabolic trough solar collectors by comparing a rhombus-shaped absorber with a conventional circular absorber. The analysis considers two rim angles of the parabolic trough, specifically 80° and 90°. Fluid flow rates ranging from 200 to 600 L per minute and inlet fluid temperatures spanning from 400 to 650 K are evaluated for each configuration. The objective is to determine the impact of absorber shape, rim angle, flow rate, and inlet temperature on the thermal performance and exergy efficiency of the system. Additionally, a slope error range of 0 to 2.5 mrad is incorporated into the study. The optical efficiency, thermal efficiency, exergy efficiency, and overall efficiency of the parabolic trough solar collector are estimated and compared for both absorber shapes. Results indicate that the thermal performance of the collector improves significantly with the rhombus-shaped absorber, showing maximum increases of 2.88% in thermal efficiency, 1.45% in exergy efficiency, and 1.4% in overall efficiency compared to the conventional circular absorber. These findings provide valuable insights for optimizing the design of parabolic trough solar collectors to enhance their overall efficiency and energy conversion effectiveness.

7 August 2018 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
Verified
Journal Article
Closed access
RDRamesh K Donga
Ramesh K Donga
SKSuresh Kumar
Suresh Kumar
In the present study, the concentration ratio of the parabolic trough collector using rhombus tube absorber has been estimated. An analytical technique has been developed to determine the optimum size of the rhombus tube absorber for given trough dimensions. The optimum size of the rhombus tube absorber is 13.8% smaller than the circular tube absorber for the LS3 trough with no change in intercept factor. The maximum improvement in the concentration ratio is found to be 31.5% for the troughs with rim angle 90° in comparison to circular tube absorber. Results also indicate that rhombus tube absorber can be employed for a range of rim angle 75 to 90 degree. Abbreviations: CR: concentration ratio; CSP: concentrated solar power; MCRT: Monte Carlo ray tracing; PTC: parabolic trough collector

1 January 2021 in Journal of Thermal Engineering
Verified
Journal Article
Closed access
PDF file
RDRamesh K Donga
Ramesh K Donga
SKSuresh Kumar
Suresh Kumar
AKAbhay Kumar
Abhay Kumar
In the present study, the effect of receiver position error on the optical and thermal performance of a parabolic trough collector (PTC) has been studied. Optical analysis of the PTC has been carried out by using Monte Carlo ray tracing (MCRT) method. The solar heat flux profile obtained from the optical analysis is coupled with the finite volume method (FVM) to study the thermal performance of the PTC. Simulations have been done for experimental SEGS LS2 solar collector used in Sandia National Laboratories. Syltherm 800 has been considered as heat transfer fluid (HTF). Receiver position errors in two directions i.e. along optical axis and lateral direction, have been taken. Results show that the receiver position error substantially influences the solar heat flux distribution and hence the temperature distribution on the absorber tube. The maximum circumferential temperature difference over the absorber tube increases up to by 199.7 K with receiver dislocation along the optical axis. The effects of the receiver position error on the optical efficiency and collector efficiency have also been studied. A maximum drop of 32% in the optical efficiency is observed when the receiver is displaced from the focus by 1.63% of focal length of the collector in both directions. The collector efficiency decreases by up to 14% when the receiver is offset by 1.63% of focal length of the collector along optical axis (away from the trough).

11 January 2023 in International Journal of Aeroacoustics
Verified
Journal Article
Closed access
Ashish KarnAshish Karn
Ashish Karn
RARitvik Anand
Ritvik Anand
AKAditya Kataria
Aditya Kataria
RDRamesh K Donga
Ramesh K Donga
NANaman Agarwal
Naman Agarwal
VSVarun Pratap Singh
Varun Pratap Singh
The physics of music has been well studied and has provided the basis on which musical instruments are made, studied and characterized. Significant research has been conducted on the different kinds of musical instruments, which range from traditional instruments like the mridangas of India to the bagpipes of Scotland. In fact, a lot of research has been carried on the acoustics of different kinds of flutes as well, such as the Finnish kantele and the Indonesian Kompangs. The Indian subcontinent, the birthplace of transverse flutes and a host of other instruments, itself has a plethora of unique musical instruments that have been scientifically examined. Yet, the Bastar flutes of India have evaded the due scientific attention that they deserve owing to their unique sound generation mechanism. Quite strangely and surprisingly, these Bastar flutes are a unique genre of flutes that don’t require lips to be played, and are quite intriguing. The current research explores the aeroacoustics of a Bastar flute via experimental measurements, computational simulations and analytical formulations. The results demonstrate that the amplitude produced is directly proportional to the number of rims present. This are also responsible for producing a low-frequency, high-amplitude melodious sound. It also suggests that the underlying mechanism behind sound generation in a Bastar flute is a unique blend of edge tone and a jet tone, demonstrating a rare phenomenon not seen in traditional musical instruments. This uncommon phenomenon has the potential to unlock several new applications in the field of acoustics.