Optics InfoBase is the Optical Society's online library for flagship journals, partnered and copublished journals, and recent proceedings from OSA conferences.
Integrated polarization beam splitters based on birefringent directional couplers are demonstrated. The devices are fabricated in bulk fused silica glass by femtosecond laser writing (300 fs, 150 nJ at 500 kHz, 522 nm). The birefringence was measured from the spectral splitting of the Bragg grating resonances associated with the vertically and horizontally polarized modes. Polarization splitting directional couplers were designed and demonstrated with 0.5 dB/cm propagation losses and −19 dB and −24 dB extinction ratios for the polarization splitting.
Microfluidic channels and Bragg Grating Waveguides (BGWs) were simultaneously fabricated inside fused silica glass by means of femtosecond laser exposure followed by chemical etching. Evanescent field penetration of the waveguide mode into the parallel microfluidic channel induced Bragg resonant wavelength shifts to enable refractive index characterization of the fluidic medium in the 1 to 1.452 range. Laser exposure was optimized to fabricate devices with optically smooth channel walls and narrow Bragg resonances for high sensing response at 1560 nm wavelength. Reference gratings were also employed in the optical circuit for temperature and strain compensation. These devices open new directions for optical sensing in three-dimensional optofluidic and reactor microsystems.
Femtosecond laser (300 fs, 500 kHz, 522 nm) fabrication of optical waveguides in bulk silica glass is extended to waveguide retarders. We study the merits of nanograting orientation (perpendicular or parallel to the waveguide) for generating high and low birefringence waveguides. This is used together with other exposure condition to control the waveguide birefringence between 10−5 and 10−4 permitting for the simultaneous fabrication of the waveguides and the tuning of the retardance demonstrating quarter and half-wave retarders in the 1200 nm to 1700 nm spectrum. The wavelength dependence of the birefringence is also characterized over a range of exposure conditions.
Femtosecond laser-fabricated waveguides have been formed into helical paths throughout the cladding of single-mode optical fibers to demonstrate a strain-independent fiber torsion sensor. A comparison between a Bragg grating sensor and a Mach–Zehnder based on helical waveguides (HWs) showed a much weaker twist sensitivity of 1.5 pm/(rad/m) for the grating in contrast with a value of 261 pm/(rad/m) for the interferometer. The HW geometry provided an unambiguous determination of the rotational direction of the twist while facilitating a convenient and efficient means for optical coupling into the single-mode core of the fiber. The flexible three-dimensional writing by the femtosecond laser fabrication method enabled the direct inscription of compact and robust optical cladding devices without the need for combining or splicing multiple-fiber segments.
23 October 2020 in Journal of Lightwave Technology
Co-packaged optics in next-generation datacenters require the assembly of multiple components on the same multichip module (MCM) and interconnection with hundreds of optical fibers. A novel photonic packaging substrate is required to leverage high-throughput electronic assembly with high precision optical alignment. This report highlights the results of glass substrate optimization to include optical waveguides, a fiber connector and chip interfaces, as well as features for electrical connectivity, as a potential component for a co-packaging solution. Glass with smooth surfaces and high precision alignment features enables surface mounted flip-chip assembly of electrical integrated circuits, photonic components, and optical fiber connectors. All components will be placed by vision alignment using precise fiducials or passive alignment in mechanical features to the surface of the glass substrate with optical and electrical interconnects. Flip-chip assembly of photonic components is enabled by evanescent coupling with couplers having a minimum non-linear taper length of 1.5 mm. The designed interface loss to the integrated ion-exchanged glass waveguides is less than 1 dB with an interface which is robust to lateral misalignment of up to 4 microns. Light can be transmitted in the glass substrate with a propagation loss of 0.1 dB/cm. Fiber interfaces are mechanically and thermally decoupled from the photonic component and glass waveguides can fan-out the component pitch from 50 microns to 250 microns of the MTP-16 ferrule connector. The solder reflow compatible connector receptacle is passively aligned and demonstrate with an average loss of 0.68 dB.