Milad Niaz Azari

Dr. Milad Niaz Azari

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 August 2019 in Scientia Iranica
Verified
Journal Article
Open access
PDF file
Amir M. Fathollahi-FardAmir M. Fathollahi-Fard
Amir M. Fathollahi-Fard
MAMilad Niaz Azari
Milad Niaz Azari
Mostafa Hajiaghaei-KeshteliMostafa Hajiaghaei-Keshteli
Mostafa Hajiaghaei-Keshteli
The Red Deer Algorithm (RDA) is one of recent metaheuristic algorithms inspired by the behavior of red deers during a breading season. The RDA revealed its performance for a variety of combinatorial optimization problems in different real-world applications. In this paper, the parameters and operators of RDA using some adaptive strategies have been modified to improve the performance of this optimizer. To prove the efficiency of Improved RDA (IRDA), not only some benchmarked functions are utilized but also a Direct Current (DC) brushless motor design as one of real-world engineering design issues. The results of developed IRDA have been compared with its general idea and existing algorithms from the literature. This comparative study confirms that the offered IRDA outperforms the other algorithms and provide very competitive results. Scientia Iranica (SCI)

27 April 2020 in IET Electric Power Applications
Verified
Journal Article
Open access
PDF file
SMSajjad Mohammadi
Sajjad Mohammadi
JKJames Kirtley
James Kirtley
MAMilad Niaz Azari
Milad Niaz Azari
Analytical models are widely employed in the design of electromagnetic devices. This study presents a flux‐tube model for axial‐flux eddy‐current couplers with surface magnets. Thanks to the developed three‐dimensional magnetic equivalent circuit, the proposed model is able to handle complex geometries and take into account all dimensional parameters and material properties such as iron saturation and permanent magnet (PM) characteristics. In addition, the associated practical design considerations including iron saturation, demagnetisation criteria, actual current paths, and heating conditions are analytically presented. Also, a three‐dimensional finite‐element analysis is utilised in the assessment of the model. Finally, a prototype is made to experimentally analyse the design and confirm analytical and numerical results.

25 October 2022 in IET Power Electronics
Verified
Journal Article
Open access
MAMohammad Amani
Mohammad Amani
MAMilad Niaz Azari
Milad Niaz Azari
Mohammad RezanejadMohammad Rezanejad
Mohammad Rezanejad
Recently, the demand for switched‐capacitor converters has increased due to the use of a low voltage input source. This article aims to improve some weak points of these inverters, such as the high number of elements by presenting a novel single‐source high step‐up multi‐level inverter topology. The proposed inverter consists of a switched‐capacitor cell with self‐balancing capability. The proposed converter uses a low voltage DC source to charge a series of capacitors stage by stage to increase the amplitude of the capacitors multiple times the input voltage. These capacitors which work as asymmetrical sources can generate a high‐amplitude AC output voltage level and hence reduce the number of DC sources and semiconductors which leads to the simplicity of structure. Since the proposed converter is using low voltage single DC source it can be used in a renewable energy application. Another aspect of this converter is producing negative levels in the output voltage without using a high‐voltage full‐bridge inverter and reducing the number of components. To verify the proposed multi‐level inverter operation, a 9‐level prototype is simulated in MATLAB/Simulink and implemented in the laboratory. The simulation and test result of the inverter confirm the validity of the proposed scheme.

11 November 2019 in IET Electric Power Applications
Verified
Journal Article
Open access
PDF file
MSMehdi Samami
Mehdi Samami
MAMilad Niaz Azari
Milad Niaz Azari
The purpose of the reverse power (RP) protection is essentially to prevent severe damage to the generator prime mover. For this aim, directional relays are usually utilised. RP condition (RPC) leads to initial oscillations of power and frequency which might exceed the RP threshold and lead to mal‐operation of the relay. Therefore, assigning a time delay is essential to reduce the oscillations. However, this strategy increases the relay trip time, which leads to enhancing the motoring time and the risk of damage to the prime mover. This study proposes a novel algorithm to detect RPC in synchronous generators, based on some easily accessible quantities including active power ( P ), load angle ( ), internal voltage ( ), terminal voltage ( V ) and the phase difference between voltage and current ( ). This scheme utilises two criterions including the sign of and also comparing V with tangential component of on V ( ). This algorithm is independent of the size and type of load and is also capable of discriminating RPC with other potential faults. The performance of the proposed approach has been verified with Matlab software and the obtained simulation results show the fastest operation and highest reliability of the proposed technique compared to others.

10 May 2021 in IETE Journal of Research
Verified
Journal Article
Closed access
RSReza Fathi Shoob
Reza Fathi Shoob
MAMilad Niaz Azari
Milad Niaz Azari
The loss of excitation (LOE) is a very common fault in synchronous machine operations and can be caused by a short circuit in the field winding, unexpected operation of the field breaker. Several methods are proposed to detect LOE, but most of them are impedance-based. It is possible that these methods will not be able to identify between LOE and stable power swing (SPS). In this paper, a new method for LOE fault detection is presented, which is designed based on the derivative of the terminal voltage and the derivative power angle of the synchronous generator. According to the proposed idea, complete simulation studies have been performed by considering different fault modes in the synchronous generator and the different conditions governing it to check the accuracy of the performance. These studies show that the proposed algorithm is faster and more accurate in detecting LOE fault. It also has higher security in distinguishing LOE fault from SPS.

1 November 2019
Verified
Open access
PDF file
MAMilad Niaz Azari
Milad Niaz Azari
VLVasiye Lohrasbi
Vasiye Lohrasbi
SMSeyed Abdolah Mousavi
Seyed Abdolah Mousavi
Today, with the high promotion of technology and the expansion of industries, electric motors are used extensively and consume a large part of the electrical energy produced by power plants. Therefore, researchers and experts have always sought solutions to make electric motors with high reliability and low losses. The machines are made of a high temperature superconducting motor with high efficiency are called high temperature superconductor -induction synchronous motor (HTS-ISM). In this paper, the high-temperature superconducting induction/synchronous motor (HTS-ISM) is studied. Optimizing of torque density and the structural dimensions of HTS-ISM is done using one of the newest optimization methods, the collective decision optimization algorithm (CDOA). The results show a torque of about 51.75% increase via the optimization process. Also commonly used optimization method, particle swarm optimization algorithm (PSO) method was implemented to compare the results. The comparison has proved that the CDOA method high capability to optimize the motor design parameters. All of the algorithms in this paper is performed with MATLAB software.