The purpose of hydraulic barriers, such as geosynthetic clay liners (GCLs), is to isolate waste liquids from the environment. Bentonite clay is widely used in GCLs because of its elevated sealing capacity in the presence of water and its ability to restrict the migration of solutes (chemico-osmotic efficiency or semi-permeable membrane behaviour). However, exposure to high concentrations of inorganic solutions can change the clay fabric increasing its hydraulic conductivity and degrading its membrane behaviour, with a consequent harm to the environment. The aim of this research was to study the hydraulic and chemico-osmotic performance of amended clays. For this purpose, an engineered clay (HYPER clay) was developed through treatment of a natural bentonite with an anionic polymer and the results were compared with two amended clay materials (multi-swellable bentonite (MSB) and a dense prehydrated GCL (DPH GCL)). To demonstrate the potential benefits of polymer treatment, material characterisation through X-ray diffraction analysis, density of solid particles, Atterberg limits, and swelling tests was performed on treated and untreated samples. Subsequently, hydraulic conductivity and chemico-osmotic tests were performed with CaCl2 solutions on treated and untreated clays, to evaluate the modified clays resistance to chemical attack. The results of this research showed that the present amendment technology has a great potential for future GCL applications. X-ray diffraction analysis demonstrated the intercalation of the polymer in the interlayer region of the clay inducing a dispersed clay structure. The swell index and the liquid limit of the clay increased with increasing polymer dosage suggesting a potential benefit of the polymer on preserving the hydraulic performance of the clay. Unlike the untreated clay, HYPER clay treatment maintained low hydraulic conductivity of the clay to CaCl2 even in the long term and protected the clay against the destructive role of diffusion, maintaining the initial osmotic efficiency in the long term. Test results were also compared with other amended clays MSB and DPH GCL. These two amended clay materials displayed a chemico-osmotic behaviour at the steady state similar to that observed on untreated clay. On the other hand, the preservation of the chemico-osmotic efficiency of the HYPER clay with time suggests that the carboxymethyl cellulose was not flushed out during the long period of permeation with deionised water.
Chemically modified bentonites are being developed with the aim of preserving low hydraulic conductivity in the presence of potentially aggressive permeants in pollutant-containment applications. ‘Multiswellable’ bentonite (MSB) has been obtained by treating standard sodium bentonite with propylene carbonate. Research on the engineering properties of MSB has focused mainly on permeability and chemical compatibility. Solute diffusion and membrane behavior in MSB have not yet been investigated. A combined chemico-osmotic/diffusion test was performed on a MSB specimen using a 5 mM CaCl2 solution. Permeability with distilled water and with the 5 mM CaCl2 solution was measured prior to and after the chemico-osmotic/diffusion tests. The material exhibited time-dependent membrane behavior with a peak osmotic efficiency value (ω) of 0.172 that gradually shifted to zero upon breakthrough of calcium ions. Effective diffusion coefficients of calcium and chloride ions were in the range commonly described for untreated bentonite at similar porosities. After the chemico-osmotic/diffusion stage and permeation with 5 mM CaCl2, the hydraulic conductivity of MSB increased from 1.1 × 10−11 m/s to 7.0 × 10−11 m/s. The MSB was apparently converted into a calcium-exchanged bentonite at the end of the test. Prehydration and subsequent permeation might have contributed to elution of the organic additive from the clay. Further investigation is recommended to clarify the effect of prehydration on the hydraulic performance of MSB in the presence of potentially aggressive permeants.
Dense prehydrated geosynthetic clay liners (DPH-GCLs) are a particular type of GCL which, unlike conventional GCLs manufactured with dry bentonite, contain bentonite prehydrated during manufacturing. DPH-GCLs are produced by a patented process that includes bentonite prehydration with a polymer solution and vacuum extrusion. This paper describes the results of permeability tests that were carried out using flexible-wall permeameters to investigate the hydraulic conductivity of a DPH GCL to water, natural seawater and a 12.5 mmol/l CaCl2 solution. Moreover, the efficiency of the 0.1 m overlap seams between DPH-GCL panels has been investigated by means of a medium-scale permeameter able to accommodate specimens 0.305 m in diameter. Test results showed that the DPH GCL has very low hydraulic conductivity to water (10−12–10−11 m/s) and preserve low permeability, of the order of 10−11 m/s, in the presence of relatively high calcium concentration in the permeating liquid. However, the efficiency of overlap seams can be affected by the permeant type. In the presence of permeant liquids that inhibit swelling (e.g. seawater), the hydraulic efficiency of the seams needs to be improved by adding bentonite paste at the overlap interface. The hydraulic performance of the DPH-GCL is attributed to the combination of prehydration, densification and chemical amendment.