AISI 321 stainless steel is widely used in chemical pipelines and nuclear power, prompting research on its high-temperature performance and corrosion resistance. This review focuses on the effects of alloy elements, second-phase particle formation, and heat treatment processes on the microstructure and properties of AISI 321 stainless steel. Fine tuning of alloying elements can affect the mode and effect of dynamic recrystallization, altering the high-temperature flow deformation of AISI 321 stainless steel. In order to achieve phase equilibrium, the relationship between corrosion resistance and high-temperature creep behavior and high-temperature mechanical behavior in the presence of second-phase particles was also analyzed. This review outlines the basic heat treatment procedures for improving material properties, providing a new perspective for solution treatment and improving corrosion resistance. In addition, the latest research progress on other factors affecting the high-temperature performance of AISI 321, such as coatings, was briefly introduced.
Nanometer hydroxyapatite (n-HA) powders were synthesized by the chemical precipitation method, and a novel ZnO/HA composite, which consisted of second-phase particles with different sizes and distributions, was successfully fabricated. ZnO/HA composites were prepared by using powder sintering with different Zn contents and a prefabrication pressure of 150 MPa. Microstructure and local chemical composition were analyzed by a scanning electron microscope (SEM) and energy-dispersive spectrometer (EDS), respectively. The phase composition and distribution of the composite were determined with electron back-scattered diffraction (EBSD) and an X-ray diffractometer (XRD), respectively. The experimental results of the XRD showed that the chemical precipitation method was a simple and efficient method to obtain high-purity n-HA powders. When the sintering temperature was lower than 1250 °C, the thermal stability of HA was not affected by the Zn in the sintering process. Due to sintering in an air atmosphere, the oxidation reaction of Zn took place in three stages, and ZnO as the second phase had two different sizes and distributions in the composites. The compressive strength of ZnO/HA composites, of which the highest was up to 332 MPa when the Zn content was 20%, was significantly improved compared with pure HA. The improvement in mechanical properties was mainly due to the distribution of fine ZnO particles among HA grains, which hindered the HA grain boundary migration and refinement of HA grains. As grain refinement increased the area of the grain boundary inside the material, both the grain boundary and second phase hindered crack development in different ways.
Annealing plays an important role to adjust structures and properties of ferromagnetic shape memory alloys. Thermal annealing effects on structural and magnetic properties of Fe 46 Mn 26 Ga 28 FSMA have been investigated at different temperatures. Rietveld refinements of neutron diffraction patterns display that the formation of the ɣ phase in Fe 46 Mn 26 Ga 28 annealed at 1073 K is Fe-rich Ga-poor cubic phase. The atomic occupancies of the alloys are determined due to the neutron's capability of differentiating transition metals. Different annealing treatment introduces magnetic characteristic that is associated with distinctive structural changes in crystal.
Color metallographic samples of H59 brass alloy have been prepared by aqua regia etching. In this paper, combined with XRD (X-ray diffraction), traditional metallographic analysis, FE-SEM (field emission scanning electron microscopy), and EBSD (electron backscattering diffraction), the effect of the color metallographic method on the microstructure characterization of the H59 brass alloy was analyzed. The experimental results showed that α phases and β phases could be distinguished clearly, and the phase morphology, distribution, and content could be expressed accurately with an average error value of 5.25% for the α phase and 4.71% for the β phase. The average error rate of the phase content characterization was 4.98% (less than 5%) with the color metallographic method. In addition, it was also found in the study that the brightness and darkness of the β phase would be related to the grain orientation, and the bright grains would correspond to the low-index surface, and the dark grains to the high-index surface. As a low-cost, fast, and efficient characterization technique, the experimental results show that color metallography (CM) could replace electron backscattering diffraction (EBSD) for the analysis of the phase composition, phase distribution, phase content, and grain orientation of brass alloys, which would provide an experimental basis for optimizing alloy properties and expanding applications.
28 November 2025 in Journal of Materials Engineering and Performance