Madeline A Morales

Dr. Madeline A Morales

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

12 May 2025 in Journal of Composite Materials
Verified
Journal Article
Closed access
MMMadeline A Morales
Madeline A Morales
BLBradley D. Lawrence
Bradley D. Lawrence
THTodd C. Henry
Todd C. Henry
This study examines the flexural properties of 3D-printed composites reinforced with short and continuous carbon fibers in a polyamide (PA) matrix before and after conditioning at 22°C/90% relative humidity. Flexural tests were performed on as-printed “dry” and conditioned “wet” samples at temperatures of 22–50°C. The materials tested were Onyx (PA with short carbon fiber reinforcement), Onyx + cCF (Onyx reinforced with continuous carbon fibers), and ULTEM 9085 (polyetherimide blend), a moisture and temperature resistant thermoplastic. Results showed that Onyx and Onyx + cCF were significantly affected by both moisture and temperature. At room temperature, Onyx dry exhibited 18% and 15% greater flexural modulus and strength, respectively, than Onyx wet, but the properties of Onyx dry decreased more rapidly than Onyx wet with increasing temperature, leading to a 68% and 29% greater flexural modulus and strength, respectively, for Onyx wet at 50°C. Onyx + cCF absorbed the greatest amount of moisture, leading to the greatest rate of decrease in flexural modulus and strength with increasing temperature. These results demonstrate the need to more thoroughly characterize the effects of moisture and temperature on the mechanical properties of 3D printed PA composites to understand their performance in applications requiring environmental exposure.

1 August 2023 in Journal of Composite Materials
Verified
Journal Article
Closed access
MMMadeline A Morales
Madeline A Morales
THTodd C Henry
Todd C Henry
BLBradley D Lawrence
Bradley D Lawrence
NBNatasha Bradley
Natasha Bradley
KKKeaton W Klaff
Keaton W Klaff
LSLourdes G Salamanca-Riba
Lourdes G Salamanca-Riba
The mechanical properties of a unidirectional carbon-fiber reinforced polymer (CFRP) laminate with Cu mesh layers were investigated for use in aerospace applications as a multifunctional structural and electromagnetic interference shielding component. Nanoindentation was used to study the fiber/PEEK and Cu/PEEK interfaces. A data analysis methodology is presented to assess the interfacial strength from plots of hardness and modulus versus distance from fiber/Cu edge. The results indicated that annealing resulted in enhanced adhesion at the fiber/PEEK interface. Additionally, indents near the Cu/PEEK interface indicated poor interfacial adhesion. Bulk mechanical testing was performed to determine the effect of adding Cu mesh layers on the mechanical properties of the laminate. Additional Cu mesh layers decreased the tension, shear, and bending strength/modulus, while the open hole compression strength increased. This indicates that the Cu/PEEK interfaces weaken the laminate and lower the tension, shear, and bending strength by delamination.

4 October 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
KTKartik Tripathi
Kartik Tripathi
MHMohamed H. Hamza
Mohamed H. Hamza
MMMadeline A Morales
Madeline A Morales
THTodd Henry
Todd Henry
AHAsha Hall
Asha Hall
ACAditi Chattopadhyay
Aditi Chattopadhyay
A novel modeling approach is developed for investigating the effectiveness of buckypaper (BP), a porous membrane made of a highly cross-linked network of carbon nanotubes, in improving the electromagnetic interference (EMI) shielding properties of carbon fiber-reinforced polymer (CFRP) composites. The methodology uses quantum tunneling-based equivalent electrical circuits and Monte Carlo simulations to predict the frequency-dependent electrical conductivity and EMI shielding effectiveness (SE) of the hybrid BP/CFRP composites. The study examines a signal frequency range of 50 MHz to 12 GHz that includes the very high and X-band. The results show that at a frequency of 12 GHz, the transverse conductivity increases to approximately 12.67 S/m, while the longitudinal conductivity decreases to about 3300 S/m from an initial value of 40,000 S/m. These results are then integrated into the ANSYS High-Frequency Structure Simulator to predict SE by simulating the propagation of electromagnetic waves through a semi-infinite composite shield element. The numerical simulations illustrate that incorporating BP significantly improves the SE of CFRP composites beyond 2 GHz owing to its high conductivity in that frequency range. For instance, at 12 GHz signal frequency, adding a single BP interleaf enhances the SE of a [90, 0] laminate by up to ~64%.

20 January 2026 in MRS Communications
Verified
Journal Article
Open access
PDF file
JAJeffrey T. Auletta
Jeffrey T. Auletta
KHKevin P. T. Haughn
Kevin P. T. Haughn
MMMadeline A Morales
Madeline A Morales
THTodd Henry
Todd Henry
This work presents an application of electroadhesion (EA) where a soft substrate is used to accommodate misalignments and surface roughness increasing normal & peel force potential. Poor alignment during multi-agent contact will create multi-axial loading requiring greater normal and peel strength than is normally considered for EA clutching and braking. Results show compliant backing increases the EA normal (8–24 kPa), peel (2–4 kPa), and shear tractions (20–106 kPa) at the expense of only contact stiffness. The displacement over which the contact maintained a traction was also increased with a soft backing increasing the contact energy in all cases. Graphical Abstract

2 May 2025 in International Journal of Micro Air Vehicles
Verified
Journal Article
Open access
THTodd Henry
Todd Henry
KHKevin Pt Haughn
Kevin Pt Haughn
MMMadeline A Morales
Madeline A Morales
JHJohn T Hrynuk
John T Hrynuk
This work presents the development of a novel, articulated small uncrewed aerial system (sUAS) tail with coupled twist-pitch motion via a ball-and-socket joint. The ball-and-socket joint is controlled by a five-bar linkage which allows two servos to work together in twist-pitch motion, as opposed to dedicated traditional elevator and rudder servo control. The articulated tail is constructed of synthetic feathers which slide over one another via a splay degree of freedom controlled by a third servo. Additive manufacturing is leveraged in the construction of all parts of a wind tunnel model with continuous carbon fiber (CCF) reinforcement, which increased the structural stiffness from 1–2 GPa for Nylon to 15–20 GPa with CCF reinforcement. Wind tunnel test results are presented for 5 and 7 m/s wind speed with body angles of-5° to 45° angle of attack and twist-pitch articulation of −30° to 45° and −45° to 45° respectively. This articulated tail design was capable of enabling fine five axis control (e.g., no roll moment control) via pitch and twist morphing across a broad range of angles of attack and airspeeds.