Maxim Sergeevich Konstantinov

Mr. Maxim Sergeevich Konstantinov

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2023 in Symmetry
Verified
Journal Article
Open access
PDF file
DCDaria Chernysheva
Daria Chernysheva
MKMaxim Sergeevich Konstantinov
Maxim Sergeevich Konstantinov
ESEkaterina Sidash
Ekaterina Sidash
TBTatiana Baranova
Tatiana Baranova
VKVictor A Klushin
Victor A Klushin
NSNina Smirnova
Nina Smirnova
Nowadays, commercial electric double-layer supercapacitors mainly use porous activated carbons due to their high specific surface area, electrical conductivity, and chemical stability. A feature of carbon materials is the possibility of obtaining them from renewable plant biomass. In this study, fungi (Fomes fomentarius) were used as a bio-template for the preparation of carbon fibers via a combination of thermochemical conversion approaches, including a general hydrothermal pre-carbonization step, as well as subsequent carbonization, physical, or chemical activation. The relationships between the preparation conditions and the structural and electrochemical properties of the obtained carbon materials were determined using SEM, TEM, EDAX, XPS, cyclic voltammetry, galvanostatic measurements, and EIS. It was shown that hydrothermal pretreatment in the presence of phosphoric acid ensured the complete removal of inorganic impurities of raw fungus hyphae, but at the same time, saved some heteroatoms, such as O, N, and P. Chemical activation using H3PO4 increased the amount of phosphorus in the carbon material and saved the natural fungus’s structure. The combination of a hierarchical pore structure with O, N, and P heteroatom doping made it possible to achieve good electrochemical properties (specific capacitance values of 220 F/g) and excellent stability after 25,000 charge/discharge cycles in a three-electrode cell. The electrochemical performance in both three- and two-electrode cells exceeded or was comparable to other biomass-derived porous carbons, making it a prospective candidate as an electrode material in symmetrical supercapacitors.


1 November 2025 in Journal of the Electrochemical Society
Verified
Journal Article
Closed access
AGA. V. Gracheva
A. V. Gracheva
KKKristina Klyukova
Kristina Klyukova
VMV. S. Makhina
V. S. Makhina
Nikolai MorozovNikolai Morozov
Nikolai Morozov
MKMaxim Sergeevich Konstantinov
Maxim Sergeevich Konstantinov
VAViktor V Avdeev
Viktor V Avdeev
Spheronized particles of natural graphite with different diameters were obtained using a centrifugal impact method. Particle shape evolution during spheronization was studied, focusing on how active surface area and substructural modifications affect lithium-ion intercalation efficiency. An average particle sizes up to 20 μm (roundness 0.9) yielded a discharge capacity of 330–340 mAh g −1 and a coulombic efficiency exceeding 90%, attributable to improved particle contact, a larger intercalation area, and reduced diffusion limitations. Further fragmentation of graphite to sizes below 5 μm compromises the mechanical integrity of the particles, alters intercalation kinetics, destabilizes charge–discharge cycling, and ultimately results in a decrease in coulombic efficiency. It is shown that the classifier performs not only particle size separation, but also promotes increased particle spheronization and an enhancement in specific surface area (SSA) at constant processing time. During mechanical treatment, SSA increases while the average nanocrystallite size decreases, allowing for the introduction of a generalized parameter—the specific number of graphene layers on the active surface area. This parameter exhibits a strong correlation with specific discharge capacity (R 2 = 0.997) and enables prediction of anode material performance.

11 October 2024 in Processes
Verified
Journal Article
Open access
PDF file
Nikolai MorozovNikolai Morozov
Nikolai Morozov
VGViktor Gubin
Viktor Gubin
DVDmitriy V. Vakhrushin
Dmitriy V. Vakhrushin
MKMaxim Sergeevich Konstantinov
Maxim Sergeevich Konstantinov
RMRoman Minushkin
Roman Minushkin
VAViktor V Avdeev
Viktor V Avdeev
An automated system for measuring the thermal conductivity of functional and structural materials was developed. The main building blocks of the setup are the following: heating unit and cooling unit creating a heat flux gradient in the test sample; thermal resistances for temperature registration and control; and thermal pads for better contact between parts of the setup and the sample. The effect of the thermal conductivity of thermal pads and thermal resistances on the distribution of thermal fields in the developed setup was studied by computer modelling. A control software for the measuring setup was developed based on the hardware implementation of the steady-state Fourier’s law-based method for the determination of thermal conductivity. The stopping criterion for the setup control software is the equality of heat fluxes in the heating and cooling units, as well as the stability of the thermal conductivity coefficient readings. The testing and calibration of the device were carried out using a sample of pure aluminum (99.999 wt.% Al). It was found that the experimental value of the thermal conductivity coefficient of the aluminum sample at room temperature (T = 22 °C) is <λ> = 243 ± 3 W/m·K. This value of the thermal conductivity coefficient is consistent with the literature data and experimental values obtained by the laser flash method, which ranges within λ = 210–260 W/m·K.

24 October 2024 in Materials
Verified
Journal Article
Open access
PDF file
MGMariya D. Gritskevich
Mariya D. Gritskevich
AGAlexandra Gracheva
Alexandra Gracheva
MFMariya S. Filippova
Mariya S. Filippova
MKMaxim Sergeevich Konstantinov
Maxim Sergeevich Konstantinov
RARashit R. Aitbaev
Rashit R. Aitbaev
VAViktor V Avdeev
Viktor V Avdeev
Synthetic graphite of complex fractional composition was mixed with phenolic resin as a binder and pore-forming component. The mixtures were pressed and subsequently heat-treated to obtain porous matrices. The structural transformations of phenolic resin by heating up to 900 °C in oxygen and inert gas media were studied and the patterns of amorphization of fixed carbon formed on the walls of the pore system during carbonization were investigated. We found regularities in the changes in matrix volume density in the function of the open porosity and the average pore diameter. It is shown that, in order to obtain graphitized carbon matrices with a density of 1 g/cm3 and an open porosity of at least 50%, it is necessary to introduce no more than 20% of phenolic resin into the molding powder with an equal content of 60, 100 and 250 μm graphite fractions. This allows for high intensity and completeness of bulk silicon infiltration.

17 November 2025 in Modelling and Simulation in Materials Science and Engineering
Verified
Journal Article
Closed access
KKKristina Klyukova
Kristina Klyukova
MKMaxim Sergeevich Konstantinov
Maxim Sergeevich Konstantinov
VMV S Makhina
V S Makhina
AGA V Gracheva
A V Gracheva
Nikolai MorozovNikolai Morozov
Nikolai Morozov
VAViktor V Avdeev
Viktor V Avdeev
Modeling of pyrolytic carbon (PyC) coating on spheronized graphite particles was performed with the goal of developing a high-performance anode material for lithium-ion batteries. The model takes into account convective and radiative heat transfer, particle movement in a fluidized bed, benzene pyrolysis kinetics and carbon deposition in view of the adhesion coefficient. It has been shown that efficient benzene decomposition for PyC coating formation occurs at temperature of 1000 °C–1100 °C. A nitrogen pulse feed rate of 10 pulses min −1 maximizes particle concentration in the benzene active decomposition zone. A semi-empirical model predicting PyC coating thickness as a function of temperature and particle diameter was presented. The calculated layer thickness varies from 20 to 45 nm and is in good agreement with the experiment. The obtained anode material exhibits ⩽ 5% loss in specific discharge capacity at 2 C and recovers up to 99% capacity at 0.1 C.