Amoxicillin is one of the broad-spectrum β -lactam antibiotics widely used in the treatment of many diseases. It is inevitable that 4-hydroxyphenylglycine (4-HPG) and 6-Aminopenicylanic acid (6-APA), which are used during the production of this antibiotic, are incorporated into the molecular lattice of the product as impurities. Today, many expensive methods and chemical devices are used for the purification of Amoxicillin by determining 6-APA and 4-HPG, which are defined as impurities. In this study, it was aimed to develop a fast, simple, and specific UV-spectrophotometric method for the determination of 4-HPG and 6-APA. Another aim of this article is to cause as little harm as possible to the environment and human health by using as few chemicals as possible throughout the study. In this study, all attempts to determine 6-APA and 4-HPG, which are impurities in the production of amoxicillin, were carried out with the help of a UV/VIS spectrophotometer. Also, Four different concentrations of NaOH were used as a solvent for each impurity. UV spectra of 4-HPG and 6-APA concentrations between 210 and 400 nm were measured. In the literature, the UV spectrum of 4-HPG has been revealed for the first time in this study and examined in detail. The UV spectrum of 4-HPG was characterized in 3 regions. Again, the response of 6-APA to different NaOH concentrations was demonstrated for the first time in this study. It was determined that the peaks of 6-APA dissolved in NaOH shifted from 222 nm to 227 nm depending on the concentration amount. In addition, it is an ideal green procedure that makes a difference in the literature, as the study is carried out for the control and determination of impurities without the use of any organic solvents or chemicals harmful to the environment.
27 November 2018 in International Journal of Computational and Experimental Science and Engineering
Today, with the globalization of the world, traders have almost removed the borders. Therefore, there has been a considerable increase in demand for people to reach each other. This also led to the increase in maritime transport which has approximately 80% of the volume of worlds’ freight load and also is the most economical mode of transportation. Despite being the most environmentally friendly transport system, the current CO2 emission rate due to sea transport is 2.5%. Also, 26% of CO2 emissions and energy consumption resulting from maritime transportation is caused by container ships which only generate 16% of world fleet. In this context, container transport has been examined in terms of CO2 emissions. Slower steaming requires less bunker consumption and fewer bunkering port calls thus lowering CO2 emissions compared to steaming at normal speeds. However, it takes more navigation time and vessels to meet the vessel-routing schedule but it can also reduce fuel cost. This study investigates CO2 emissions responsible for a container ship to determine bunker fuel saving and CO2 reduction strategies for container shipping lines. A case study was carried out using the real shipping data of a container ship with a capacity 1880 TEU between Ambarlı and Savannah ports. Additionally, two different scenarios have been proposed to reduce the emission of a real container ship in operation.
Saf bir kristal ürün elde etmek için tekrar tekrar uygulanan kristalizasyon basamakları veya farklı kimyasallara başvurulması, bitmiş ürünün veriminde farklı sorunlara neden olabilir. Bundan dolayı, kristal ağın içerisindeki safsızlıklar, ana ürünü etkilemeden uzaklaştırılmalıdır. Bu çalışmada, Amoksisilin trihidrat (Amct) ve safsızlık olarak 4-hidroksifenilglisin (4-HPG) kullanılmıştır. Amct kristal kafesinden, safsızlık olarak 4-HPG’nin yıkama yöntemleri kullanılarak uzaklaştırılması gösterilmiştir. Ayrıca, bu çalışmada ilk kez, yıkama verimi ile yıkama yöntemleri, çözeltiler ve sıcaklıklar arasındaki ilişkiyi incelemek için Taguchi metodu kullanılmıştır. Denemelerde bir Büchner cam hunisi istenilen sıcaklıkta ve ürün kaybı olmadan çalışılacak şekilde yeniden tasarlanmıştır ve denemeler burada yapılmıştır. Bu çalışma, farklı yıkama yöntemleri, kullanılan Taguchi metot ve yeniden tasarlanan Büchner cam hunisi ile literatüre farklılık katmaktadır. Etki grafiklerinden yıkama verim değerlerini etkileyen faktörler sırasıyla yıkama yöntemi, sıcaklık ve çözelti olarak belirlenmiştir. En yüksek verim, tek aşamalı yıkama yöntemi ile Etilalkol kullanılarak 15°C’de elde edilmiştir.