We report on preparation of Ir and IrO2 electrodes and its applications to planar and three-dimensional (3D) PZT capacitors solely by MOCVD using a novel liquid Ir precursor, Ir(EtCp) (CHD). Continuous 15–50 nm-thick Ir films with a pure metallic phase were successfully grown at 250-350°C on SiO2/Si without an incubation time. Ir electrodes showed 40–60% step coverage on stepped substrates with aspect ratios of 0.5–2.0. Fatigue free planar and 3D-Ir/PZT/Ir capacitors with 2Pr of 27–36 μ C/cm2 were successfully fabricated solely by MOCVD. IrO2 electrodes were grown at 400°C by 2-step MOCVD using surface oxidized Ir seeds. Planar PZT capacitors with IrO2 bottom and Ir top electrodes showed D-E hysteresis loops with 2Pr of 27 μ C/cm2 and endurance property with no degradation up to 1010 switching cycles by bipolar pulses of ± 5 V and 500 kHz.
1 August 2011 in Clinical and Experimental Nephrology
Control of the charge state of the nitrogen-vacancy (NV) center is crucial because of its instability and its transitions between the negative (NV–) and neutral (NV0) NV charge states under laser irradiation In this study, we fabricated an n-i-n junction, with an i-layer sandwiched between two phosphorus-doped n-layers; then, we measured the charge state of NV centers under steady state and laser irradiation in a known band structure where the Fermi energy changes gradually. The steady-state charge state measured by a nondestructive single shot exhibited stable NV– and NV0 signals when the Fermi level was even slightly above and below the transition level, respectively. This result indicates that the charge state can be significantly stabilized through band engineering. Both charge-state populations were observed only when the Fermi level was close to the transition level. Under continuous green laser irradiation, the ratio of NV– measured by the photoluminescence spectra changed gradually with the Fermi level in the depletion layer because of the balance between excitation from the laser and the supply of charge from the band. This outcome agrees reasonably with the calculated bands. Furthermore, we measured the PL spectra of the ensemble NV centers and discovered that their charge state can be well-controlled, as in the single NV center. The charge state of the i-layer at the interface can be stabilized by depositing a thin n-layer on the surface. These results would contribute significantly to improve sensor performance.
With the advancement of non-classical light sources such as single-photon and entangled-photon sources, innovative microscopy based on quantum principles has been proposed for traditional microscopy. This paper introduces the experimental demonstration of a quantum polarization microscopic technique that incorporates a quantum-entangled photon source. Although the point that employs the variation in polarization angle due to reflection or transmission at the sample is similar to classical polarization microscopy, the method for constructing the image contrast is significantly different. The image contrast is constructed by the coincidence count of signal and idler photons. In the case that the coincidence count is recorded from both the signal and idler photons, the photon statistics resemble a thermal state, similar to the blackbody radiation, but with a significantly higher peak intensity in the second-order autocorrelation function at zero delay that is derived from the coincidence count, while, when the coincidence count is taken from either the signal or idler photon only, although the photon state exhibits a thermal state again, the photon statistics become more dispersive and result in a lower peak intensity of the autocorrelation function. These different thermal states can be switched by slightly changing the photon polarization, which is suddenly aroused within a narrow range of the analyzer angle. The autocorrelation function g2(0) at the thermal state exhibits a sensitivity that is three times higher compared to the classical coincidence count rate, and this concept can be effectively utilized to enhance the contrast of the image. One of the key achievements of our proposed method is ensuring a low power of illumination (in the order of Pico-joules) for constructing the image. In addition, the robustness without any precise setup is also favorable for practical use. This polarization microscopic technique can provide a superior imaging technique compared to the classical method, opening a new frontier for research in material sciences, biology, and other fields requiring high-resolution imaging.
When the fluorescence of a material under transparent conductive films is measured, it is sometimes required that the transparent conductive films have low fluorescence intensity to prevent stray light. Herein, the oxygen partial pressure during sputtering is varied and the transmittance, resistivity, and fluorescence intensity are measured to clarify the cause of the fluorescence of indium tin oxide (ITO) and In2O3. The fluorescence intensity of both ITO and In2O3 decreases with an increase in the oxygen partial pressure in the case of as‐deposited films. The cause of fluorescence is considered to be oxygen vacancies. ITO can maintain low resistivity even with a small amount of oxygen vacancies since it contains SnO2, which generates carriers. High‐temperature annealing also introduces other defects, which increases the fluorescence intensity.
29 July 2025 in Japanese Journal of Applied Physics
Quantum imaging is an advanced method for microscopy and investigating the optical properties of materials or biomedical samples with high accuracy, low noise, and minimal photo-damage. Previously, we proposed a quantum imaging technique where variations in polarization angle due to reflection or transmission enhanced image contrast in the second-order autocorrelation function at zero delay, g²(0). However, the observed image resolution was insufficient. In this study, we optimized the coincidence window to better distinguish photon statistics and used an objective lens to focus the entangled photon beams, improving image quality. Although effective for various samples, this method has limitations for samples exhibiting polarization disturbances such as photon scattering. Nevertheless, it demonstrates superior imaging performance under noisy conditions and low illumination, offering potential for high-quality quantum imaging applications.