Powerslide of an automobile may be defined as a steady-state cornering motion at a large side slip angle of the vehicle, considerably large traction forces and a large negative steering angle of the handwheel. In this case the front wheels direct towards the outside of the turn. As this extrem driving condition, which can be seen e.g. in Rallye sports, is hardly addressed in literature so far, this paper investigates the respective handling characteristics. Therefore, a nonlinear four-wheel vehicle model is applied including nonlinear tyre characteristics, the load transfer between inner and outer wheels and the influence of the traction forces on the lateral tyre forces. A basic stability analysis reveals the unstable nature of the steady-state powerslide motion of a certain test vehicle. To approve the numerical findings, measurements have been performed with a sports utility vehicle with rear-wheel drive at various speeds on a wet circular test track.
Due to increasing demands for time and cost efficient vehicle and driver assistant systems development, numerical simulation of closed-loop manoeuvres becomes increasingly important. Thus, the driver has to be considered in the modelling. On the basis of a two-layer approach to model a driver's steering behaviour, the field of application is extended to higher lateral accelerations in this study. An analytical method to determine the driver parameters is presented, which is based on the two-wheel vehicle model. The simulation results are determined using a full vehicle model including all essential nonlinearities. Standard manoeuvres in the nonlinear range of vehicle handling behaviour are performed. A cornering manoeuvre is chosen to show the characteristics of the proposed driver model.
The tyre model performance test (TMPT) provides information about the efficiency and problems of the simulation sequence from tyre measurements (tyre modelling and parametrization) to multibody-system (MBS) software integration. Based on test rig tyre measurements with respect to vehicle-handling behaviour and higher-frequency-range tests (running over a cleat; vibration modes), tyre models have to be provided in a way that they can be connected with the standard Tyre interface (STI) or a modified tyre interface to at least one of the three MBS programs ADAMS, DADS and SIMPACK. The test conditions and the simulation test rig were defined in advance by an international group of experts. Four tyre model providers participated for the handling (low-frequency) manoeuvres and four for the low- and higher-frequency-ranges. Since a planned feedback from the MBS simulation results (they were done by the MBS-program providers) to the tyre model providers was not completely finished, the results shown are preliminary only. For the steady-state behaviour, all tyre models show good agreement with measurements for lateral and longitudinal tyre forces while, for the self-aligning torque, larger differences appear. For ‘crossing of a cleat’, all high-frequency-range models show good agreement with measurements as well but, for some tests (e.g. sinusoidal sweeps), qualitative differences even between MBS programs for the same tyre model can be noticed. This indicates that the application of tyre models within MBS programs requires some preliminary testing and maybe additional checks before using them for vehicle dynamics analysis.
Wheel shimmy and wobble are well-known dynamic phenomena at automobiles, aeroplanes and motorcycles. In particular, wobble at the motorcycle is an (unstable) eigenmode with oscillations of the wheel about the steering axis, and it is no surprise that unstable bicycle wobble is perceived unpleasant or may be dangerous, if not controlled by the rider in time. Basic research on wobble at motorcycles within the last decades has revealed a better understanding of the sudden onset of wobble, and the complex relations between parameters affecting wobble have been identified. These fundamental findings have been transferred to bicycles. As mass distribution and inertial properties, rider influence and lateral compliances of tyre and frame differ at bicycle and motorcycle, models to represent wobble at motorcycles have to prove themselves, when applied to bicycles. For that purpose numerical results are compared with measurements from test runs, and parametric influences on the stability of the wobble mode at bicycles have been evolved. All numerical analysis and measurements are based on a specific test bicycle equipped with steering angle sensor, wheel-speed sensor, global positioning system (GPS) 3-axis accelerometer, and 3-axis angular velocity gyroscopic sensor.
So far fundamental papers on the understanding of the wobble mode at motorcycles have been published, but in contrast, little research has been published on the wobble mode at bicycles. Wobble denotes a characteristic unstable oscillatory mode dominated by oscillations of the front wheel about the steering axis. The wobble mode of a trekking bicycle at low speeds has already been analysed, where no influence of the rider's hands on the steering system is taken into account. The wobble mode of a racing bicycle at higher speeds has not been addressed in more detail so far. The paper points out the difference between a trekking bicycle and a racing bicycle in particular with respect to the wobble mode. Different geometry, mass and stiffness properties of both types of bicycles and different characteristic positions of the rider are considered. As the wobble at racing bicycles often occurs at high speeds, when riding down a grade with hands on a dropped handlebar, a passive rider model, that takes into account the movement of the rider's arms, is presented.