Corson Cramer

Dr. Corson Cramer

orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 May 2021 in Journal of the American Ceramic Society
Verified
Journal Article
Closed access
PDF file
CCCorson Cramer
Corson Cramer
AEAmy M. Elliott
Amy M. Elliott
Edgar Lara-CurzioEdgar Lara-Curzio
Edgar Lara-Curzio
AFAlexis Flores‐Betancourt
Alexis Flores‐Betancourt
MLMichael J. Lance
Michael J. Lance
KNKashif Nawaz
Kashif Nawaz

1 November 2019 in Heliyon
Verified
Journal Article
Open access
CCCorson Cramer
Corson Cramer
PNPeeyush Nandwana
Peeyush Nandwana
JYJiaqiang Yan
Jiaqiang Yan
SESamuel F. Evans
Samuel F. Evans
AEAmy M. Elliott
Amy M. Elliott
Mariappan Parans ParanthamanMariappan Parans Paranthaman
Mariappan Parans Paranthaman
High silicon (Si) electrical steel has the potential for efficient use in applications such as electrical motors and generators with cost-effective in processing, but it is difficult to manufacture. Increasing the Si content beyond 3 wt.% improves magnetic and electrical properties, with 6.5 wt.% being achievable. The main goal of this research is to design, develop, and implement a scalable additive manufacturing process to fabricate Fe with 6.5 wt.% Si (Fe-6Si) steel with high magnetic permeability, high electrical resistivity, low coercivity, and low residual induction that other methods cannot achieve because of manufacturing limitations. Binder jet additive manufacturing was used to deposit near net shape components that were subsequently sintered via solid-state sintering to achieve near full densification. Here, it is shown that the use of solid-state sintering mitigates cracking since no rapid solidification occurs unlike fusion-based additive technologies. The Fe-6Si samples demonstrated an ultimate tensile strength of 434 MPa, electrical resistivity of 98 μΩ cm, and saturation magnetization of 1.83 T with low coercivity and high permeability. The results strongly supports to replace the only available 0.1 mm thick chemical vapor deposition (CVD) produced Si steel using the cost effective AM method with good mechanical and magnetic properties for motor applications.

31 May 2018 in Journal of Electronic Materials
Verified
Journal Article
Closed access
PDF file
CCCorson Cramer
Corson Cramer
HWHsin Wang
Hsin Wang
KMKaka Ma
Kaka Ma

1 October 2019 in Materials & Design
Verified
Journal Article
Open access
CCCorson Cramer
Corson Cramer
AEAmy M. Elliott
Amy M. Elliott
JKJames O. Kiggans
James O. Kiggans
BHBianca Haberl
Bianca Haberl
DADavid C. Anderson
David C. Anderson

1 February 2020 in International Journal of Refractory Metals and Hard Materials
Verified
Journal Article
Closed access
CCCorson Cramer
Corson Cramer
TATrevor G. Aguirre
Trevor G. Aguirre
NWNatalie R. Wieber
Natalie R. Wieber
RLRichard A. Lowden
Richard A. Lowden
ATArtem A. Trofimov
Artem A. Trofimov
AEAmy Elliott
Amy Elliott

18 September 2020 in International Journal of Ceramic Engineering & Science
Verified
Journal Article
Open access
PDF file
CCCorson Cramer
Corson Cramer
HAHerb Armstrong
Herb Armstrong
AFAlexis Flores‐Betancourt
Alexis Flores‐Betancourt
LHLu Han
Lu Han
AEAmy M. Elliott
Amy M. Elliott
KNKashif Nawaz
Kashif Nawaz
The effect of polymer infiltration and pyrolysis (PIP) cycles with polycarbosiloxane on the microstructure, air leak rate, and properties of SiC composites manufactured by a combination of binder jet 3D printing and PIP is reported. The density, Young's modulus and flexural strength of disk‐shaped components increased with the number of PIP cycles. In the case of density, it increased from 2.05 g/cm3 in one PIP cycle to 2.33 g/cm3 after three PIP cycles, while values of flexural strength and Young's modulus at room temperature after three PIP cycles reached 66.8 ± 2.5 MPa and 69.5 ± 2.8 GPa, respectively. Conversely, the air leak rate was found to decrease with number of PIP cycles, and it reached a value of 4 mbar‐L/s after three cycles. The instantaneous coefficient of thermal expansion of the composite was found to change minimally with the number of PIP cycles and had a value of 4 ± 1.2 ppm/°C between 200°C and 1000°C. Thermal conductivity was found to increase with number of PIP cycles and to decrease with temperature. For example, after three PIP cycles it was found to change from 6.72 ± 0.08 to 6.98 ± 0.08 W/mK at 25°C and 7.36 ± 0.08 to 7.96 ± 0.08 W/mK at 300°C. These values were lower than those of crystalline SiC because of the amorphous nature of the matrix and the presence of pores and cracks.