In an earlier study we reported that G(o) phase peripheral blood mononulclear cells (PBMC) exposed to low-level (SAR = 0.18 W/kg) pulse-modulated 1300 MHz microwaves and subsequently cultured, demonstrate changed immune activity (Dabrowski et al., 2003). We investigated whether cultured immune cells induced into the active phases of cell cycle (G(1), S) and then exposed to microwaves will also be sensitive to electromagnetic field. An anechoic chamber of our design containing a microplate with cultured cells and an antenna emitting microwaves (900 MHz simulated GSM signal, 27 V/m, SAR 0.024 W/kg) was placed inside the ASSAB incubator. The microcultures of PBMC exposed to microwaves demonstrated significantly higher response to mitogens and higher immunogenic activity of monocytes (LM index) than control cultures. LM index, described in detail elsewhere (Dabrowski et al., 2001), represents the monokine influence on lymphocyte mitogenic response. The results suggest that immune activity of responding lymphocytes and monocytes can be additionally intensified by 900 MHz microwaves.

The paper presents microstrip patch antennas, which are based on the fractal antenna concept, and use planar periodic geometries, providing improved characteristics. The properties of the fractal structure were used in a single-fractal layer design as well as in a design, which employs fractals on both the upper and bottom layers of the antenna. The final structure, i.e., a double-fractal layer antenna has been optimized to enhance bandwidth and gain of the microstrip antenna. The proposed geometry significantly improved antenna performance. The antenna could support an ultra-wide bandwidth ranging from 4.1 to 19.4 GHz, demonstrating higher gain with an average value of 6 dBi over the frequency range, and a radiation capability directed in the horizontal plane of the antenna.

(2003). Immunotropic Effects in Cultured Human Blood Mononuclear Cells Pre‐exposed to Low‐Level 1300 MHz Pulse‐Modulated Microwave Field. Electromagnetic Biology and Medicine: Vol. 22, No. 1, pp. 1-13. doi: 10.1081/JBC-120020347

The reflection and absorption properties of powdered nanocrystalline FeSiBCuNb (“Finemet”) alloy at microwaves have been presented. To visualize the shielding ability of this material, the complex permittivity and permeability of pulverized Finemet in the frequency range from 0.2 to 10 GHz have been studied. To measure the permittivity and permeability of powdered Finemet, the modification of the Nicolson, Ross, and Weir method was presented. The modification of this method was mainly based on the unwrapping technique of the measured S-parameter phases. The investigation of permittivity and permeability was realized for pure powders. Four groups of powders with different particle sizes below 200 μm have been investigated. To assess the shielding effectiveness of the nanocrystalline Finemet, two attempts were analyzed. The investigation of the reflection loss of material layer with metal sheet attached to the backside as a reflector was investigated. On the other hand, the reflection and absorption factors of 3-mm-thick layer in free space were additionally analyzed. The obtained results show that the pulverized nanocrystalline Finemet alloy with particle size below 25 μm possesses good absorption properties and, for such particles, the absorption factor is significantly higher than the reflection factor.

This article investigates the issue of measuring high-power microwave (HPM) pulses. The high energy of these pulses poses a significant threat to many electronic systems, including those used to manage critical infrastructure. This work focuses on requirements for a potential portable measurement device and suggests the application of a method for this purpose, involving the use of a D-dot sensor and a rapid A/D converter. The applied converter enables recording the time waveform on the measuring chain output, also in the case of repetition and time duration of HPM signals. The authors also present a quantitative description of signal processing by the analogue section of the measurement chain solution presented herein and suggest algorithms for digital processing of the signals, the objective of which is to minimize low-frequency interference in the process of reconstructing the time waveform of an electric field using numerical integration.

Within this study, we explored the augmented security measures for the electronics of unmanned aerial vehicles (UAVs) within an RF environment. UAVs are commonly utilised across various sectors, and their use as auxiliary platforms for cellular networks, as parallel networks working in tandem with ground-based base stations, holds considerable promise. In this context, ensuring the uninterrupted operation of UAVs is a paramount objective. However, the considerable external electromagnetic interference emitted by existing base stations may jeopardise the functionality of UAV electronics. This could potentially lead to an unintended flight path and a sudden cessation of communication with the operator. To mitigate the detrimental impact of the RF field, we advocate covering the UAV casing with reduced graphene oxide (RGO). The efficacy of RGO’s shielding effectiveness (SE) was investigated over a frequency spectrum from 100 MHz to 10 GHz. Our scrutiny of this property was centred around the measurement of scattering matrix coefficients of the unadulterated material—without additives of any kind. Our findings show that this material is a favourable candidate for UAV absorbers due to its low reflection coefficient coupled with its high absorption capacity. The studied absorber ensures an SE value of 25 dB and 30 dB for a 3 mm layer at frequencies of 3.6 GHz (pertaining to the 5G system) and 5.8 GHz (pertaining to LTE), respectively.