This study explores the acceptance of different wood coverages on building facades with the aim of optimization of materials, and in turn improving overall sustainability. It firstly develops the principal physical variables and evaluation criteria; then, test models are created using an orthogonal design experiment; finally, two evaluation methods are used to comprehensively test acceptance, based on a questionnaire and an eye-tracking study. The results show that: (1) The effects of the amount of wood coverage and the wood patterns are significant, whereas the effect of material combinations is insignificant. (2) The acceptance of building facades is at the highest level when the amount of wood coverage is 65%. (3) The amounts of wood coverage for facades in the range of 35% to 50% are effective when designing the facade of wood buildings, in order to implement the dual targets of saving wood and higher acceptance.

Photovoltaic (PV) glazing is widely used in the building sector for its power generation advantages. However, its low transmittance reduces solar heat gain, limiting energy-saving effectiveness in heating regions. To address this, the present study proposes a novel PV energy-saving window that reduces heating load by separately controlling its components—PV glazing, insulated shutter, and clear glazing—through three control modes: Mode 1 controls insulated shutter, Mode 2 controls insulated shutter and PV glazing, and Mode 3 controls insulated shutter and clear glazing. First, the energy-saving benefits of the window were confirmed through in situ testing. Next, using a validated model, the correlation between key factors and heating load was analyzed under the above three modes. Finally, the impact of configurations on heating load under the three control modes was clarified. The main findings are as follows: (1) When PV glazing is controlled, clear glazing layers become the primary factor influencing the heating load. (2) In Modes 1 and 3, the configurations have a greater impact on heating load, reducing it by 34.62% and 39.60%, respectively, while Mode 2 shows a reduction of 17.93%. (3) Mode 2 is the optimal control mode, confirming the effectiveness of controlling PV glazing to reduce heating load.

Wood presentation of modern wood building facades relating to the expression of the essential characteristics of architecture, utilization efficiency of wood and acceptance of architectural image,etc. However, relevant studies are obviously insufficient. This paper makes a statistical analysis of outstanding wood structure space cases which be selected, tries to reveal the expression rule of major timber application variables of wood coverage, materials collocation, wood form and wood color under the limitation of the main influencing factors of building function, building form and building scale.The purpose of this study is to explore the wood presentation rule of modern wood building Facades under the influence of building factors.

To address the imbalance between the “ecological advantage” and “economic benefit” of wooden structure buildings, this study examines two structural construction methods utilizing inexpensive and readily available small-diameter round timber as the primary material. It demonstrates the advantages of these two structural systems in terms of material consumption, life cycle carbon emissions, and economic efficiency. Through the research methods and processes of “Preliminary analysis–Proposing the construction system–The feasibility analysis of structural technology–Efficiency assessment”, the sustainable wood structure technical system suitable for the development of China is explored. The main conclusions are as follows: (1) Employing the preliminary analysis method, this paper examines and analyzes construction cases that primarily utilize small-diameter round timber as the main material. It delineates specific construction types based on the characteristics of small-diameter round timber. Additionally, it technically reconstructs the methodology for utilizing small-diameter round timber. (2) Two lattice structural systems are proposed, leveraging the mechanical properties and fundamental morphological characteristics of inexpensive and readily available small-diameter round timber of fast-growing Northeast larch. The technical feasibility of these two small-diameter log structure systems is validated through simulation analysis of their spatial threshold suitability. (3) This study conducted a comprehensive comparison between the two small-diameter round timber structural systems and the conventional grain-parallel glued laminated timber (Cross-Laminated Timber) frame structural systems. The analysis was performed from three perspectives. As the primary structural material, grain-parallel glued laminated timber frame structural systems exhibits significant advantages in terms of timber utilization per unit area of the structural system. From a life cycle carbon emission analysis perspective, compared to grain-parallel glued laminated timber frame structures, small-diameter round timber structures can achieve carbon emission reductions ranging from 79.19% to 97.74%. Additionally, the unit area cost of small-diameter round timber structures is reduced by 21.02% to 40.42% relative to grain-parallel glued laminated timber frame structures. Consequently, it can be concluded that small-diameter round timber structural systems possess technical feasibility and construction advantages for small and medium-sized buildings, offering practical value in optimizing technical systems to meet the objective needs of ecological construction.