The efficiency of wireless power transfer (WPT) systems is highly dependent on the load, which may change in a wide range in field applications. Besides, the detuning of WPT systems caused by the component tolerance and aging of inductors and capacitors can also decrease the system efficiency. In order to track the maximum system efficiency under varied loads and detuning conditions in real time, an active single-phase rectifier (ASPR) with an auxiliary measurement coil (AMC) and its corresponding control method are proposed in this paper. Both the equivalent load impedance and the output voltage can be regulated by the ASPR and the inverter, separately. First, the fundamental harmonic analysis model is established to analyze the influence of the load and the detuning on the system efficiency. Second, the soft-switching conditions and the equivalent input impedance of ASPR with different phase shifts and pulse widths are investigated in detail. Then, the analysis of the AMC and the maximum efficiency control strategy are provided in detail. Finally, an 800-W prototype is set up to validate the performance of the proposed method. The experimental results show that with 10% tolerance of the resonant capacitor in the receiver side, the system efficiency with the proposed approach reaches 91.7% at rated 800-W load and 91.1% at 300-W light load, which has an improvement by 2% and 10% separately compared with the traditional diode rectifier.
17 January 2017 in IEEE Transactions on Power Electronics
It is more convenient and safer to employ inductive power transfer (IPT) systems to charge the battery pack of electric bicycles (EBs) than conventional plug-in systems. An IPT charging method suitable for charging massive EBs is proposed to achieve constant current (CC) and constant voltage (CV) output without feedback control strategies or communication link between transmitter side and receiver side. Two ac switches (ACSs) and an auxiliary capacitor utilized at receiver side are employed to be operated once to change the charging modes from CC mode to CV mode. The characteristics of the load-independent current output in the CC mode and load-independent voltage output in the CV mode are achieved by properly selecting the passive parameters of inductances and capacitors, so that no sophisticated control strategies are required to regulate the output as per the charging profile. The feasibility of proposed method has been verified with an experimental prototype in form of efficiency, stability of output current and voltage in CC/CV mode. The simple and economical approach is suitable for the massive EBs charging system with only one inverter, especially in China.
27 February 2018 in IEEE Transactions on Power Electronics
Inductive power transfer (IPT) for battery charging applications has significant advantages over the traditional plug-in system. Since misalignment between the primary and secondary windings is inevitable, it is of significance to improve the misalignment tolerance of IPT systems with constant-current (CC) and constant-voltage (CV) outputs for battery charging. In this paper, the load-independent output characteristic of the hybrid topology and the function switching between CC and CV of the reconfigurable topology are analyzed. Besides, a hybrid and reconfigurable IPT system with 3-D misalignment tolerance for CC and CV outputs is proposed, simplifying or even canceling control schemes. Moreover, a novel parametric design method is given for the IPT system, which can suppress the fluctuation of the output voltage/current within a certain range of misalignment. In order to validate the performance of the proposed topology, a 1-kW prototype is built, and the corresponding experiments are carried out. In the CC/CV mode, the system can operate with the longitudinal misalignment to 50% when the load varies from 36 to 480 Ω, and the fluctuation of the output current/voltage is within 5%. Similarly, the misalignment in Y- and Z-axis is 12.5% and 33.3%, respectively.
11 December 2017 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Wireless power transfer (WPT) chargers for electric bicycles (EBs) have many advantages over transitional plug-in systems. However, to meet the charge requirements, the traditional charger needs a dedicated inverter to achieve constant current (CC) output or constant voltage (CV) output. A hybrid topology based EBs charging strategy is proposed using a single high-frequency inverter (HFI) to charge massive EBs, and one charging stand can be shared to charge EBs with various specifications of batteries. Configurable CC and CV outputs can be realized by turning on/off two AC switches (ACSs) without adopting sophisticated control schemes or wireless communication links. Besides, zero phase angle (ZPA) switching of HFI can be realized, and then the system efficiency is increased. Finally, the proposed method is verified by experiments with various charging conditions. The results show that the fluctuation margins of charging currents and charging voltages in the whole charging process are both less than 2.5% and the maximum efficiency reaches 91.90%. With the merit of the proposed approach, the reduction of construction cost and the control complexity is achieved. Thus, it might be one of the most promising solutions for charging massive EBs in some regions like China.
High-density surface electromyography (HD-sEMG) and deep learning technology are becoming increasingly used in gesture recognition. Based on electrode grid data, information can be extracted in the form of images that are generated with instant values of multi-channel sEMG signals. In previous studies, image-based, two-dimensional convolutional neural networks (2D CNNs) have been applied in order to recognize patterns in the electrical activity of muscles from an instantaneous image. However, 2D CNNs with 2D kernels are unable to handle a sequence of images that carry information concerning how the instantaneous image evolves with time. This paper presents a 3D CNN with 3D kernels to capture both spatial and temporal structures from sequential sEMG images and investigates its performance on HD-sEMG-based gesture recognition in comparison to the 2D CNN. Extensive experiments were carried out on two benchmark datasets (i.e., CapgMyo DB-a and CSL-HDEMG). The results show that, where the same network architecture is used, 3D CNN can achieve a better performance than 2D CNN, especially for CSL-HDEMG, which contains the dynamic part of finger movement. For CapgMyo DB-a, the accuracy of 3D CNN was 1% higher than 2D CNN when the recognition window length was equal to 40 ms, and was 1.5% higher when equal to 150 ms. For CSL-HDEMG, the accuracies of 3D CNN were 15.3% and 18.6% higher than 2D CNN when the window length was equal to 40 ms and 150 ms, respectively. Furthermore, 3D CNN achieves a competitive performance in comparison to the baseline methods.
21 December 2017 in IEEE Transactions on Industrial Electronics
Electric bicycles (EBs) are becoming increasingly popular in some regions such as China and Europe. However, wireless power transfer (WPT) for charging massive EBs poses a challenge related to the cost of WPT system (WPTS), especially in China, where EBs application is so sensitive to the product price. This paper presents an optimization method of the passive components for the S-LCC topology to decrease the cost of the overall system. With the novel method, the number of passive components can be optimized to the minimum and still with constant current and constant voltage outputs. A novel compensation method with an inductor array is also proposed to guarantee an inductive input impedance of WPTS, achieving soft switching and reducing the high switching losses of the high-frequency inverter (HFI). To demonstrate the validity of the proposed methods, an experimental setup is built. The performance of two WPTS indicates that massive EBs can be charged with only one HFI, and the cost of the overall system decreases accordingly.