α particles must be monitored to be managed as radioactive diagnostic agents or nuclear activity indicators. The new generation of perovskite detectors suffer from limited energy resolution, which affects spectroscopy and imaging applications. Here, we report that the solution-grown CsPbBr3 crystal exhibits a low and stable dark current (34.6 nA·cm−2 at 200 V) by thinning the as-grown crystal to decrease the high concentration CsPb2Br5 phase near the surface. The introduction of the Schottky electrode for the CsPbBr3 detector further reduces the dark current and improves the high-temperature stability. An energy resolution of 6.9% is achieved with the commercial electronic system, while the effects of air scattering and absorption are investigated. Moreover, 1.1% energy resolution is recognized by a full-customized readout application-specific integrated circuit without any additional signal processing, which matches well with the given parameters of the CsPbBr3 detector by reducing the parasitic capacitance and electronic noise.
17 November 2023 in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
The Circular Electron Positron Collider (CEPC) has been proposed to enable more thorough and precise measurements of the properties of Higgs, W, and Z bosons, as well as to search for new physics. In response to the stringent performance requirements of the vertex detector for the CEPC, a baseline vertex detector prototype was tested and characterized for the first time using a 6GeV electron beam at DESY II Test Beam Line 21. The baseline vertex detector prototype is designed with a cylindrical barrel structure that contains six double-sided detector modules (ladders). Each side of the ladder includes TaichuPix-3 sensors based on Monolithic Active Pixel Sensor (MAPS) technology, a flexible printed circuit, and a carbon fiber support structure. Additionally, the readout electronics and the Data Acquisition system were also examined during this beam test. The performance of the prototype was evaluated using an electron beam that passed through six ladders in a perpendicular direction. The offline data analysis indicates a spatial resolution of about 5 μm, with detection efficiency exceeding 99% and an impact parameter resolution of about 5.1 μm. These promising results from this baseline vertex detector prototype mark a significant step toward realizing the optimal vertex detector for the CEPC.
A high amount of hits on the vertex detector of the International Linear Collider are generated by the beam background, which leads to an increase in the data flow of the detector system. Charged particles coming from the beam background have low momentum, resulting in the generation of elongated clusters. The CMOS pixel sensor, which integrates pre-processing functions and on-chip artificial neural networks, could remove these elongated clusters. Clustering is the first step for data pre-processing and is used to collect clusters from raw data. In this paper, a pixel-level clustering algorithm with a 5×5 window executed in real-time is proposed. The algorithm is tested using 4500 frames (500 frames for each angle of incidence) of raw data (12bits/pixel) from a MIMOSA-18 sensor and compared to conventional clustering algorithms. The clustering implementation for an example array of 5×5 pixels is synthesized for different frequencies (100 and 200MHz) and ADC resolutions (4 and 8bits). The power dissipation and occupied area of the different implementations are analyzed. The hardware implementation of the algorithm provides the possibility to integrate the clustering function into the CMOS pixel sensor.
28 September 2023 in IEEE Transactions on Nuclear Science
In the International Linear Collider, charged particles that come from the beam background may hit on the vertex detector and generate elongated clusters, leading to the increasing of useless data in the detector system. In previous work, we conducted the feasibility study of a CMOS pixel sensor with on-chip artificial neural networks in order to remove the elongated clusters. The principle component analysis is a good approach, which was developed in the FPGA implementation for feature extraction. However, the principle component analysis method is challenging for the ASIC implementation. In this paper, we propose four features and corresponding two operators for feature extraction. A total of 4500 frames of raw data at nine angles of incidence are sampled from MIMOSA-18. The clustering procedure is executed on raw data to gather clusters. Two operators are achieved by C code and tested on the experimental clusters. Distributions of four features of these clusters are analyzed. Results show that these features can represent the pattern of clusters with different incident angles. The ratio of feature Summin to Summax is decreased as the incident angle increases, which verifies that the clusters are elongated at the large incident angle.