It is well known that the process of vortex breakdown plays an important role in establishing the near-field aerodynamic characteristics of fuel injectors, influencing fuel/air mixing and flame stability. The precise nature of the vortex breakdown can take on several forms, which have been shown in previous papers to include both a precessing vortex core (PVC) and the appearance of multiple helical vortices formed in the swirl stream shear layer. The unsteady dynamics of these particular features can play an important role in combustion induced oscillations. The present paper reports an experimental investigation, using particle image velocimetry (PIV) and hot-wire anemometry, to document variations in the relative strength of PVC and helical vortex patterns as the configuration of a generic fuel injector is altered. Examples of geometric changes that have been investigated include: the combination of an annular swirl stream with and without a central jet; variation in geometric details of the swirler passage, e.g., alteration in the swirler entry slots to change swirl number, and variations in the area ratio of the swirler passage. The results show that these geometric variations can influence: the axial location of the origin of the helical vortices (from inside to outside the fuel injector), and the strength of the PVC. For example, in a configuration with no central jet (swirl number ), the helical vortex pattern was much less coherent, but the PVC was much stronger than when a central jet was present. These changes modify the magnitude of the turbulence energy in the fuel injector near field dramatically, and hence have an important influence on fuel air mixing patterns.
An experimental study has been undertaken to document compressibility effects in the annular shear layers of axisymmetric jets. Comparison is made of the measured flow development with the well-documented influence of compressibility in planar mixing layers. High Reynolds number (~106) and high Mach number jets issuing from a convergent nozzle at nozzle pressure ratios (NPRs) from 1.28 to 3.0 were measured using laser Doppler anemometry instrumentation. Detailed radial profile data are reported, particularly within the potential core region, for mean velocity, turbulence rms, and turbulence shear stress. For supercritical NPRs the presence of the pressure waves in the inviscid shock cell region as the jet expanded back to ambient pressure was found to exert a noticeable effect on shear layer location, causing this to shift radially outwards at high supercritical NPR conditions. After a boundary layer to free shear layer transition zone, the turbulence development displayed a short region of similarity before adjustment to near-field merged jet behaviour. Peak turbulence rms reduction due to compressibility was similar to that observed in planar layers with radial rms suppression much stronger than axial. Comparison of the compressibility-modified annular shear layer growth rate with planar shear layer data on the basis of the convective Mach number (MC) showed notable differences; in the annular shear layer, compressibility effects began at lower MC and displayed a stronger reduction in growth. For high Mach number aerospace propulsion applications involving round jets, the current measurements represent a new data set for the calibration/validation of compressibility-affected turbulence models.
1 January 1998 in JSME International Journal Series B
Stereoscopic three-component particle image velocimetry (3C-PIV) measurements have been made in a turbulent round jet to investigate the spatio-temporal correlations that are the origin of aerodynamic noise. Restricting attention to subsonic, isothermal jets, measurements were taken in a water flow experiment where, for the same Reynolds number and nozzle size, the shortest time scale of the dynamically important turbulent structures is more than an order of magnitude greater that in equivalent airflow experiments, greatly facilitating time-resolved PIV measurements. Results obtained (for a jet nozzle diameter and velocity of 40 mm and $1~\text{m}~\text{s}^{-1}$ , giving $\mathit{Re}=4\times 10^{4}$ ) show that, on the basis of both single-point statistics and two-point quantities (correlation functions, integral length scales) the present incompressible flow data are in excellent agreement with published compressible, subsonic airflow measurements. The 3C-PIV data are first compared to higher-spatial-resolution 2C-PIV data and observed to be in good agreement, although some deterioration in quality for higher-order correlations caused by high-frequency noise in the 3C-PIV data is noted. A filter method to correct for this is proposed, based on proper orthogonal decomposition (POD) of the 3C-PIV data. The corrected data are then used to construct correlation maps at the second- and fourth-order level for all velocity components. The present data are in accordance with existing hot-wire measurements, but provide significantly more detailed information on correlation components than has previously been available. The measured relative magnitudes of various components of the two-point fourth-order turbulence correlation coefficient ( $R_{ij,kl}$ ) – the fundamental building block for free shear flow aerodynamic noise sources – are presented and represent a valuable source of validation data for acoustic source modelling. The relationship between fourth-order and second-order velocity correlations is also examined, based on an assumption of a quasi-Gaussian nearly normal p.d.f. for the velocity fluctuations. The present results indicate that this approximation shows reasonable agreement for the measured relative magnitudes of several correlation components; however, areas of discrepancy are identified, indicating the need for work on alternative models such as the shell turbulence concept of Afsar (Eur. J. Mech. (B/Fluids), vol. 31, 2012, pp. 129–139).
The components of an aeroengine gas-turbine combustor have to perform multiple tasks – control of external and internal air distribution, fuel injector feed, fuel/air atomisation, evaporation, and mixing, flame stabilisation, wall cooling, etc. The ‘rich-burn’ concept has achieved great success in optimising combustion efficiency, combustor life, and operational stability over the whole engine cycle. This paper first illustrates the crucial role of aerodynamic processes in achieving these performance goals. Next, the extra aerodynamic challenges of the ‘lean-burn’ injectors required to meet the ever more stringent NOx emissions regulations are introduced, demonstrating that a new multi-disciplinary and ‘whole system’ approach is required. For example, high swirl causes complex unsteady injector aerodynamics; the threat of thermo-acoustic instabilities means both aerodynamic and aeroacoustic characteristics of injectors and other air admission features must be considered; and high injector mass flow means potentially strong compressor/combustor and combustor/turbine coupling. The paper illustrates how research at Loughborough University, based on complementary use of advanced experimental and computational methods, and applied to both isolated sub-components and fully annular combustion systems, has improved understanding and identified novel ideas for combustion system design.