The development of radar applications usually involves a complex set of different components, which can be costly and sometimes require careful handling. By concentrating most of the radar tasks into a software-defined radio, the hardware burden is alleviated, while the processing can be efficiently developed using open-source software suites. This article describes the development of a prototype radar based on a commercial software-defined radio, using only a few extra components. It operates under the holographic principle, where excitation is performed in single frequency, continuously transmitted. The tests have shown its potential applicability, carried out in an indoor environment, including through-the-wall detection.
This article describes the challenge of a Multiple-Input Multiple-Output (MIMO) array for Brazilian Digital TV 3.0. The chosen Advanced Television Systems Committee (ATSC) 3.0 system is the first worldwide to employ $2\times 2$ MIMO antennas, which, in view of the unpredictable indoor environment and long wavelengths, is an engineering challenge. The design, focused on mass indoor environments, is oriented towards a compact, low-cost, and planar radiant system. Since the required bandwidth spans the Very High Frequency (VHF) and Ultra High Frequency (UHF) ranges, miniaturization is the first compromise rather than the standard reflection-loss parameter. Aprototype is constructed and tested inside a building room using as reception a test signal broadcast at the center frequency of 177.1428571MHz, and additionally with four different carriers (177.143MHZ, 277.143MHZ, 587.143MHz and 695.142MHZ), within an anechoic chamber. The proposed compact planar antenna covers the 174–698MHz band with envelope correlation coefficients below 0.1 and achieves realized gains of nearby 0dB. Tests in broadcast and anechoic environments confirmed its broadband performance and suitability for low-cost indoor MIMO reception in Brazil’s TV 3.0 system.
This article presents a technical analysis of the influ-ence of polarization on terrestrial reception in the TV 3.0 system, also known commercially as DTV+, focusing on the evaluation of polarization effects and their influence over the robustness influence on the robustness of Multiple-Input Multiple-Output (MIMO) operation through polarization diversity. Urban scenarios with different Line-of-Sight (LoS) conditions and two reception environments, outdoor and indoor, were modeled to assess the relative performance of Vertical (V) and Horizontal (H) linear polarizations (0° and 90°), as well as slant polarization (-45° and +45°). The methodology combines vector modeling of the electromagnetic field with parametric simulations based on distance, obstruction, and angular dispersion. The results highlight an asymmetry between V and H polarizations. Horizontal polarization shows superior performance in outdoor environments, while ±45° polarization demonstrated intermediate performance and greater vector stability. The analysis of the Effective Polarization Ratio (EPR) proved decisive in assessing reception robustness. This metric was particularly relevant in indoor reception, where vector degradation can compromise the separation of MIMO streams even at adequate power levels. It is concluded that the choice of polarization should take into account factors such as distance, obstruction, and the predominant reception type. The ±45° configuration is technically interesting due to its balance between robustness, selectivity, and coverage.
1 January 2025 in Journal of Microwaves, Optoelectronics and Electromagnetic Applications
This article describes a two-element antenna designed in a Digital Terrestrial Television Broadcasting (DTTB) Multiple Input Multiple Output (MIMO) 2×2 front antenna in the 470 to 700 MHz band. It is based on a planar, canonical, fat-dipole element with low-cost and robust characteristics. Both antenna elements are fed directly by a coaxial connector, without a balun, and have been optimized to provide low coupling, improving their combined diversity gain. The array occupies an area of 0.76λ2o x 0.51λ2o (907 cm2) at the center frequency wavelength. Measurements of the antennas in outdoor urban environments are presented with a technology proponent for the project, the Advanced Integrated Services Digital Broadcasting - Terrestrial (ISDB-T), in 8 urban sites in Rio de Janeiro, Brazil. The results showed that the proposed MIMO 2×2 antenna operates effectively in outdoor applications, is robust, has a low development cost, and has a low degree of mutual coupling.
A broadband and compact planar UHF antenna is presented for use in MIMO Digital TV indoor applications. The choice of the element and its physical implementation is oriented towards a low-profile, low-cost, and single-layer deployment. Since it is intended to be used in a 2 × 1 MIMO array, two antennas were constructed and tested to minimize their coupling to provide larger MIMO gains. Regarding the excitation, two different structures were evaluated to observe their impact on the final impedance profile. The option of an infinite balun provided a 62% fractional bandwidth (394 MHz to 747 MHz), covering the desired band and with good isolation levels when analyzed in the array. Results regarding MIMO parameters are provided herein, such as Envelope Correlation Coefficient and Total Active Reflection Coefficient, proving the potential of the proposed antenna array to be used in MIMO Digital TV applications in covering the UHF band.