The unique capabilities of Aerosol Jet® technology for noncontact material deposition with in-flight adjustment of ink rheology in microdroplets are explained based on first principles of physics. The suitable range of ink droplet size is determined from the effectiveness for inertial impaction when depositing onto substrate and convenience for pneumatic manipulation, in-flight solvent evaporation, etc. The existence of a jet Reynolds number window is shown by a fluid dynamics analysis of impinging jets for Aerosol Jet® printing with long standoff between nozzle and substrate, which defines the operation range of gas flow rate according to the nozzle orifice diameter. The time scale for ink droplets to remove volatile solvent is shown to just coincide that for them to travel in the nozzle channel toward substrate after meeting the coflowing sheath gas, enabling the in-flight manipulation of ink properties for high aspect-ratio feature printing. With inks being able to solidify rapidly, 3D structures, such as tall micropillars and thin-wall boxes, can be fabricated with Aerosol Jet® printing. Having mist droplets in the range of 1–5 μm also makes it possible to print lines of width about 10 μm.
1 October 2017 in Journal of Microelectronics and Electronic Packaging
Direct-write methods, such as the Aerosol Jet® technology, have enabled fabrication of flexible multifunctional 3-D devices by printing electronic circuits on thermoplastic and thermoset polymer materials. Conductive traces printed by additive manufacturing typically start in the form of liquid metal nanoparticle inks. To produce functional circuits, the printed metal nanoparticle ink material must be postprocessed to form conductive metal by sintering at elevated temperature. Metal nanoparticles are widely used in conductive inks because they can be sintered at relatively low temperatures compared with the melting temperature of bulk metal. This is desirable for fabricating circuits on low-cost plastic substrates. To minimize thermal damage to the plastics, while effectively sintering the metal nanoparticle inks, we describe a laser sintering process that generates a localized heat-affected zone (HAZ) when scanning over a printed feature. For sintering metal nanoparticles that are reactive to oxygen, an inert or reducing gas shroud is applied around the laser spot to shield the HAZ from ambient oxygen. With the shroud gas-shielded laser, oxygen-sensitive nanoparticles, such as those made of copper and nickel, can be successfully sintered in open air. With very short heating time and small HAZ, the localized peak sintering temperature can be substantially higher than that of damage threshold for the underlying substrate, for effective metallization of nanoparticle inks. Here, we demonstrate capabilities for producing conductive tracks of silver, copper, and copper–nickel alloys on flexible films as well as fabricating functional thermocouples and strain gauge sensors, with printed metal nanoparticle inks sintered by shroud-gas-shielded laser.
As Aerosol Jet® (AJ) printing is becoming more attractive to additive manufacturing, printed electronics, among other applications, reducing or minimizing the amount of ink droplets landing in unintended regions—known as the overspray—has been elevated on the agenda for print quality control and improvement. Many AJ users had discussed the overspray issue associated with AJ printing, while the metrology for quantified evaluation of overspray is still lacking. In this work, the likely physical mechanism for inducing overspray is analyzed along with a set of computational fluid dynamics (CFD) simulations. We then present a 2D image processing method for quantitatively evaluating the severity of overspray in terms of its percent area coverage versus a normalized distance from printed line edge. Our results show that the amount of overspray of AJ printing seems to scale with the printed line width (LW), and usually to become negligible (e.g. percent area coverage of overspray < 1%) beyond 30%–40% of LW from line edges. The overspray is shown to often decrease by increasing the jet velocity and sheath-to-mist ratio. Without loss of generality and for concise illustration, herewith we use only one representative ink to print test samples for the quantitative overspray analysis. The results have been found to bear a resemblance to AJ printed features with many other inks.
31 August 2009 in International Journal of Multiphase Flow