Piotr Uliasz

Dr. Piotr Uliasz

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2011 in Archives of Metallurgy and Materials
Verified
Journal Article
Open access
PDF file
TKTadeusz Antoni Knych
Tadeusz Antoni Knych
MPM. Piwowarska
M. Piwowarska
PUPiotr Uliasz
Piotr Uliasz

1 January 2012
Verified
Book Chapter
Closed access
PDF file
PUPiotr Uliasz
Piotr Uliasz
TKTadeusz Antoni Knych
Tadeusz Antoni Knych
MPMarzena Piwowarska
Marzena Piwowarska
JWJustyna Wiecheć
Justyna Wiecheć

4 November 2024 in Coatings
Verified
Journal Article
Open access
PDF file
EDEwa Dryzek
Ewa Dryzek
MWMiroslaw Wrobel
Miroslaw Wrobel
SDStanislaw Dymek
Stanislaw Dymek
MKMateusz Kopyściański
Mateusz Kopyściański
PUPiotr Uliasz
Piotr Uliasz
PWPiotr Wokurka
Piotr Wokurka
Serrated flow effects are visible on a metal surface even after coating. Thus, they are undesirable to manufacturers and product users. To meet the expectations of the industry, research on the conditions for serrated flow occurrence in 5019 aluminum alloy was carried out and the results were collected in the current paper. Thus, the influence of the alloy initial microstructure due to different tempers as well as plastic deformation conditions, i.e., strain rate and temperature, on the alloy stress–strain behavior was determined. Two tempers were considered: the as-fabricated F-temper and the W-temper (i.e., quenched in water after annealing at 500 °C). The synergic influence of these tempers and their tensile test conditions on the serration behavior of the stress–strain curves, i.e., the stress drop and reloading time, were also determined and categorized. Structural and X-ray diffraction studies rationalized the stress–strain characteristics according to dynamic strain aging models with positron annihilation lifetime spectroscopy providing insight into the role of lattice defects (i.e., dislocations and vacancies). The map of the serrated flow domain allowed us to obtain the activation energy of the onset of the Portevin–Le Chatelier effect equal to 56 kJ/mol. It is close to the activation energy for the pipe diffusion mechanism, obtained by applying the model formulated originally for Type B stress serration.

28 February 2022 in Archives of Metallurgy and Materials
Verified
Journal Article
Closed access
PDF file
PKP. Koprowski
P. Koprowski
MLM. Lech-Grega
M. Lech-Grega
ŁWŁ. Wodzinski
Ł. Wodzinski
BABogusław Augustyn
Bogusław Augustyn
SBSonia Boczkal
Sonia Boczkal
MOM. Ożóg
M. Ożóg
The effect of 0.2% addition of Mg, Co and Ce to 99.9% cast aluminium was studied by evaluation of changes in microstructure and mechanical properties. The microstructure was analyzed by scanning electron microscopy and transmission electron microscopy. The Al99.9 alloy contained only Al-Fe-Si phase particles. Similar Al-Fe-Si particles were observed in alloy with 0.2% Mg addition, because this amount of magnesium was fully dissolved in the solid solution. The addition of cobalt resulted in the formation of Al9.02Co1.51Fe0.47 phase particles assuming the shape of eutectic plates. The electron backscattered diffraction map made for the alloy with 0.2% Co addition showed numerous twin boundaries with distances between them in the range from 10 to 100 µm. The addition of cerium was located in the grain boundary area. Cerium also gave rise to the formation of two types of particles, i.e. Al4Ce and Al-Ce-Fe-Si. The Al-Ce-Fe-Si phase is a nucleation site for the Al4Ce phase, which forms eutectic plates. The results showed that the introduction of additives increases the mechanical properties of the cast materials. The 99.9% cast aluminium has a hardness of 16.9 HB. The addition of 0.2% by weight of Mg, Co, Ce increases this hardness to 21.8 HB, 22.6 HB and 19.1 HB, respectively.