The interaction between a planar shock wave and square and triangular bubbles containing either SF6, He, Ar, or CO2 is studied numerically. It is shown that, due to the existing large differences in the molecular weight, the specific heat ratio, and the acoustic impedance between these gases, different wave patterns and pressure distribution inside the bubbles are developed during the interaction process. In the case of heavy gases, the velocity of the shock wave propagating along the bubble inner surface is always less than that of the incident shock wave and higher than that of the transmitted shock wave. However, in the case of the light gas (He), the fastest one is the transmitted shock wave and the slowest one is the incident shock wave. The largest pressure jump is witnessed in the SF6 case, while the smallest pressure jump is seen in the helium case. There are also pronounced differences in the deformation of the investigated bubbles; while triangular bubbles filled with either Ar, CO2, or SF6 were deformed to a crescent shape, the helium bubble is deformed to a trapezoidal shape with three pairs of vortices emanating from its surface.
The interaction between a planar shock wave propagating in air and a polygonal bubble (composed of two triangles) containing two different gases is studied numerically. Studying the interaction between an oncoming shock wave with front- and rear-facing triangles containing light and heavy gases is of great importance in understanding the complex shock wave propagation, interaction and hydrodynamic instabilities as well as their effect on mitigating or enhancing the colliding shock/blast wave. Two different cases were studied: in the first case, the front triangle contained sulfur hexafluoride (SF6) and the rear one contained helium (He); while in the second case, He is in the front and SF6 in the rear triangle. As the speed of sound in He is significantly higher than that in SF6 and in air, different flow fields were evolved. When SF6 is placed in the front triangle, the shock wave transmitted through the SF6 is reflected back from the interface separating the two gases and starts propagating downstream; over the He segment of the bubble, the incident shock wave (in the open air) is already seen over the He section and it submits compression waves into the He gas. These compression waves travel upstream and downstream; in their upstream movement they generate compression waves into the ambient air ahead of the incident shock wave. The part moving downstream will hit the interface separating SF6 and He, resulting in a complex wave pattern. A completely different wave pattern is visible when He is placed in the front triangle. Now the fastest shock is the transmitted shock wave in the He section; it reaches the membrane separating the two gases well before the incident shock wave reaches this location. Unlike the previous case, now the resulting flow in the rear triangle of the bubble is affected not only by the incident shock wave but also by the transmitted compression waves from the helium section. Furthermore, when helium is placed in the front section of the bubble, the compression waves in the He impacts the rear triangle of the bubble (containing SF6) almost like a planar shock wave. This is different from the previous case where SF6 was in the front section; then the shock wave impacting on the rear bubble containing He had a completely different shape due to its propagation into the SF6 bubble. This resulted in completely different peak pressures.
1 September 2016 in European Journal of Mechanics - B/Fluids
This article reports recent experimental results in water column deformation and breakup resulting from shock wave loading. Experiments were conducted in a shock tube whose cross section was reduced from 60 mm × 150 mm to 4 mm × 150 mm by using a cookie cutter. Inside the test section a 6.4-mm diameter water column was created. The shock-wave Mach number was 1.3 at atmospheric air. Double exposure finite-fringe holographic interferometry with a double-path arrangement was used for visualization. Interferograms of the water column breakup process at various stages were collected and compared with previous experiments conducted at the Shock Wave Research Center (SWRC) with different Mach numbers and for various diameters. All the results were displayed universally in nondimensional form. Based on water column deformation, the drag coefficient was evaluated and compared with that of spherical droplets.
A numerical study investigating the interaction process between a converging shock wave and a gas bubble placed at an offset location is presented. As a first step, for proofing the reliability of the used numerical scheme, a simulation of relevant available experimental findings of Hosseini and Takayama [“Richtmyer–Meshkov instability induced by cylindrical shock wave loading of cylindrical gaseous inhomogeneities,” AIAA Paper No. 2000-2464, 2000] and Hosseini and Takayama [“Study of a converging shock wave interaction with a gaseous interfaces in an eccentric arrangement,” in Japanese Symposium on Shock Waves, 2000] is conducted; the tested gases were helium (He) and sulfur hexafluoride (SF6). The converging shock wave had a Mach number of 1.18 prior to its impact on the 50 mm diameter gas bubble. Achieving good agreement with the experimental findings ensures the reliability of the applied numerical scheme. After the converging shock wave impacted the gas bubble, different shock waves are created. These shock waves propagate differently than those observed in the case of planar shock wave impacting a cylindrical gas bubble or that of a converging shock wave where the gas bubble is located at the center. Furthermore, once the converging shock wave converged, a diverging shock wave expands and again impacts the remaining gas bubble, thus creating more complex shock wave patterns. The gas contained inside the bubble has an effect on the location of the converging shock wave focus point. In the case of the heavy gas SF6, the focus point is near the center of the converging shock wave, but in the case of light gas He, it is offset from the converging shock wave focus point and outside of the initial location of the He bubble. The new results from the current numerical simulation include more detailed results for both bubbles, which were not reported in Hosseini and Takayama [“Richtmyer–Meshkov instability induced by cylindrical shock wave loading of cylindrical gaseous inhomogeneities,” AIAA Paper No. 2000-2464, 2000] and Hosseini and Takayama [“Study of a converging shock wave interaction with a gaseous interfaces in an eccentric arrangement,” in Japanese Symposium on Shock Waves, 2000]. In addition, a shock wave focusing of the transmitted shock wave inside the SF6 bubble is observed. This later creates a secondary diverging shock wave. Higher pressure is achieved in the SF6 case.