Mechanical specific energy (MSE) has been widely used to quantify drilling efficiency and maximize rate of penetration (ROP) in oil and gas wells drilling. In this chapter, MSE models respectively for directional or horizontal drilling and rotating drilling with positive displacement motor (PDM) are established based on the evaluation of virtues and defects of available MSE models. Meanwhile methods for drilling performance prediction and optimization based on MSE technologies are presented. Field data presented in this chapter indicates that the developed MSE models estimate MSE values with a reasonable approximation in the absence of reliable torque measurements, the method for optimizing drilling parameters can estimate optimum WOB values with different RPM to drill a specific formation interval with PDM. It also show that the optimum WOB is low for rotating drilling with PDM compared with the conventional drilling without PDM, increasing WOB does not always increase ROP but is more likely to decrease ROP. The drilling performance prediction and optimization methods based on MSE technologies could be effectively used to maximize ROP and allow operators to drill longer and avoid unnecessary trips, and is worthy to be applied and promoted with highly diagnostic accuracy, effective optimizing and simple operation.

Efficient cuttings transport and improving rate of penetration (ROP) are two major challenges in horizontal drilling and extended reach drilling. A type of jet mill bit (JMB) may provide an opportunity to catch the two birds with one stone: not only enhancing cuttings transport efficiency but also improving ROP by depressuring at the bottom hole. In this paper, the JMB is further improved and a new type of depressure-dominated JMB is presented; meanwhile, the depressurization capacity of the depressure-dominated JMB is investigated by numerical simulation and experiment. The numerical study shows that low flow-rate ratio helps to enhance the depressurization capacity of the depressure-dominated JMB; for both depressurization and bottom hole cleaning concern, the flow-rate ratio is suggested to be set at approximately 1:1. With all other parameter values being constant, lower dimensionless nozzle-to-throat-area ratio may result in higher depressurization capacity and better bottom hole cleaning, and the optimal dimensionless nozzle-to-throat-area ratio is at approximately 0.15. Experiments also indicate that reducing the dimensionless flow-rate ratio may help to increase the depressurization capacity of the depressure-dominated JMB. This work provides drilling engineers with a promising tool to improve ROP.

The design of the wellbore trajectory directly affects the construction quality and efficiency of drilling. A good wellbore trajectory is conducive to guiding on-site construction, which can effectively reduce costs and increase productivity. Therefore, further optimization of the wellbore trajectory is inevitable and necessary. Based on this, aiming at the three-segment, five-segment, double-increase-profile extended reach wells, this paper considered the constraints of formation wellbore stability; formation strength; and the determination of the deviation angle, deviation point position, and target range by the work of deflecting tools. In addition, the optimization objective function of the shortest total length of the wellbore, minimum error of the second target, lowest cost, minimum friction of the lifting and lowering string, and minimum torque of rotary drilling were proposed and established. The objective function of the longest extension limit of the horizontal section of the extended reach well is established. Taking the 14-8 block of the Lufeng Oilfield in the eastern South China Sea as an example, the actual data of the field were modeled, and the independence of the objective function was verified by comparing the number of non-inferior solutions of the two objective functions. By normalizing simplified to double-, three-, and four-objective functions, using a genetic algorithm and particle swarm optimization results, it can be found that the new method of optimization design established in this paper has an obvious optimization effect compared with the original design.

In depleted offshore reservoirs, pore pressure declines and consequently horizontal in-situ stresses decrease as well. This causes a very limited well depth for extended-reach drilling targeting to offshore depleted reservoirs. In this paper, based on analyzing the safe mud weight window of the depleted offshore reservoirs, a model of predicting the Maximum Allowable Measured Depth (MAMD) for extended-reach drilling targeting to offshore depleted reservoirs is developed. Meanwhile, the numerical method of the model is proposed, and the key affecting factors of the MAMD are also investigated. The results show the pore pressure depletion has obvious effects on the MAMD. With the depletion of pore pressure, the safe mud weight window appears narrower and even disappears, consequently the predicted MAMD becomes shorter. For a normal regime depositional environment in the depleted reservoirs, it may be impossible to drill with conventional drilling method in the nearby directions of the maximum horizontal in-situ stress, while it may be much safer and attain a long MAMD when drilling in the directions near the minimum horizontal in-situ stress. Moreover, the MAMD will decrease with the increase of Poisson’s ratio and Biot’s parameter, and its response to Poisson’s ratio is more obvious. For a specific target depleted reservoir, the extended-reach drilling with a high borehole inclination may have a longer MAMD than that with a low borehole inclination. This paper presents a method for promoting the design of extended-reach drilling targeting to offshore depleted reservoirs.