Implant-associated infections are a frequent complication of surgeries involving biomaterial implants. Staphylococcus and Enterococcus species are the leading causes of infections linked to bone-anchored and joint implants. To address this challenge, developing antibacterial coatings to prevent bacterial attachment and biofilm formation on biomaterials is critical. This study aimed to evaluate the antibacterial and antibiofilm properties of two biomaterial coatings: titanium nitride (TiN) and titanium nitride with silver nanoparticles (TiN/Ag). Antibacterial activity was tested against common biofilm-forming pathogens, including Escherichia coli, Staphylococcus aureus, Enterococcus faecalis, and Enterococcus faecium. The results demonstrated that both coatings significantly reduced bacterial cell counts, with the TiN/Ag coating showing superior performance due to the addition of silver nanoparticles. This enhancement was particularly effective in reducing biofilm formation across all the tested strains, with the most pronounced effects observed for E. faecium and E. faecalis. The silver nanoparticles synergistically improved the antibiofilm properties of the TiN coating, efficiently disrupting biofilm integrity and reducing bacterial adhesion. By reducing bacterial attachment and biofilm formation on biomaterial surfaces, TiN/Ag coatings offer a promising strategy to minimize complications associated with biomaterial implants. These findings highlight the potential of TiN and TiN/Ag coatings for medical applications.

In this study, the properties of electrophoretically deposited (EPD) coatings on orthodontic implants made from Ti-6Al-4V alloy were evaluated during simulated implantation trials on animal bones. Three types of chitosan-based coatings were prepared using EPD: titanium nitride microparticles (TiNPs), titanium nitride nanoparticles (TiNNPs), and boron nitride particles (BNPs). Each of these coatings was also modified by adding a polylactic acid (PLA) layer using a dip-coating technique to compare their properties with and without this additional layer. The coatings were analysed using optical microscopy, confocal microscopy, and scanning electron microscopy (SEM) with elemental analysis. Surface roughness measurements of the coated implants were also conducted to highlight differences that could significantly influence the type and strength of the bone-implant interface, directly affecting the stability of the implant as an anchorage unit. Eventually, to evaluate the antibacterial properties of the EPD coatings, their antibacterial activity against both Gram-positive and Gram-negative bacteria strains was tested. Scanning electron observations confirmed the homogenous distribution of micro- and nanoparticles in all coatings. The highest surface roughness values were observed in layers containing titanium nitride nanoparticles (TiNNPs) and chitosan. The presence of an additional dip-coating PLA layer improved the adhesion, and its effect on the surface roughness depended on the particle size. While the antibacterial properties of the coatings show promising results, achieving optimal adhesion of the coatings to implants remains a challenge that requires further development.

The aim of the study was to develop hybrid nanomaterials based on monodisperse silica spheres as carriers for silver nanoparticles (AgNPs) or bismuth nanoparticles (BiNPs) and to evaluate their antimicrobial properties. Silica spheres were synthesized using a modified Stöber method, either unmodified or functionalized with (3-aminopropyl)triethoxysilane (APTES), prior to AgNP or BiNP deposition. The materials were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), inductively coupled plasma optical emission spectroscopy (ICP-OES), and zeta potential measurements, while antimicrobial activity was assessed by microdilution against Gram-positive (Staphylococcus aureus, Staphylococcus epidermidis, Enterococcus faecalis, Enterococcus faecium) and Gram-negative bacteria (Escherichia coli, Pseudomonas aeruginosa), with Helicobacter pylori as a clinical model. The results show that both SiO₂-AgNP and SiO₂-BiNP composites completely inhibited H. pylori and showed high activity against other pathogens, although P. aeruginosa remained less susceptible. Functionalization of AgNP-coated samples with APTES promoted uniform distribution of AgNPs, with the minimum bactericidal concentration (MBC) to minimum inhibitory concentration (MIC) ratios ranging from 1 to 4, confirming a bactericidal rather than bacteriostatic effect. In contrast, BiNP-coated samples without APTES exhibited lower MIC values from 74 to 595 μg mL⁻¹, consistent with increased Bi³⁺ release from amorphous phases. This indicates the antimicrobial potential, highlighting the role of surface functionalization in regulating ion release and biological performance, and suggesting applications in the biomedical and food industries.

The objective of this study was to investigate the physicochemical properties of hybrid coatings with titanium nitride and boron nitride nanoparticles deposited on the TiAlV medical alloy via the sol–gel process. The developed layers were intended to impart bactericidal properties and provide protection against surgical abrasions during the implantation procedure. This study focused on evaluating the microstructure (SEM + EDS), structure (XRD, FTIR), and surface properties, including wettability, surface free energy, and roughness of the synthesized layers. Our results confirmed that it was feasible to produce hybrid layers with various microstructures and diverse layer morphologies. The FTIR and XRD structural analyses confirmed the presence of an organosilicon matrix incorporating the two aforementioned types of ceramic particles.

The aim of this work was to obtain homogenous coatings containing chitosan with different concentrations of titanium nitride particles (TiN). The coatings were deposited via an electrophoretic process on an etched medically pure Ti-6Al-4V alloy. As part of the study, the zeta potential of the suspensions used for EPD coating deposition was measured, allowing for the optimization of process parameters and the assessment of suspension stability. Subsequently, the research focused on evaluating the microstructure (SEM + EDS), structure (XRD), and surface characteristics (roughness, contact angle, surface energy, microhardness, coating adhesion) of the deposited layers. SEM microscopy confirmed the effective deposition of titanium nitride particles onto the titanium alloy surface. XRD analysis proved the assumed phase composition of the coating. The increase in TiN phase content in the individual layers was confirmed. The chitosan/TiN layer’s introduction altered the alloy surface, increasing its roughness and static water contact angle. The highest roughness and hydrophobic properties were observed in the coating with a 2 wt.% concentration of titanium nitride particles. Additionally, the coating containing the highest concentration of ceramic particles (2 wt.%) exhibited the highest hardness (197 HV) among all the tested layers. However, the TiN particles incorporation in the layer decreased the adhesion strength, from 2.36 MPa (0.5 wt.% TiN) to 1.04 MPa (2 wt.% TiN). The coatings surface and structural properties demonstrate potential as protective layers for implants and are suitable for further biological studies to assess their applicability in medical and veterinary fields.