Reinforcement using an interlayer system has been demonstrated for more than four decades as a multi-purpose solution to improve performance, to extend service life and thus to reduce maintenance costs of road pavements. Among a large number of existing interlayer systems, glass fibre grids have shown effective use in pavement reinforcement with a hot mix asphalt overlay. Recently they have received increasing attention from the pavement community. However, as for other types of interlayer systems, the mechanisms underlying the effectiveness and proper installation of this type of reinforcement system are still not fully understood, and the choice of the most appropriate grid (e.g. mesh size, tensile strength) and its optimal location in the pavement system are mainly based on experience. This article presents firstly a literature review on the use of glass fibre grids in pavement reinforcement. Then some results of recent full-scale tests on the accelerated pavement testing facility of the IFSTTAR are presented. They confirm that glass fibre grid properly installed near the bottom of the asphalt layer improves significantly the fatigue life of the reinforced pavement. They also demonstrate the efficiency of glass grid use under only a thin asphalt overlay. Finally, first results obtained using an original instrumentation of glass grid strands by means of strain gages, to understand better the mechanical behaviour of the glass fibre reinforcement in a new pavement structure are described.

Classically, measurements on instrumented pavements are performed on site, under known load conditions. In such conditions, data interpretation and modelling of the pavement are relatively easy. However, on-site measurements are time consuming and costly to perform, because they require using a dedicated vehicle and closing the lane to traffic. This paper presents an experiment, where an instrumented bituminous pavement motorway section has been followed by remote monitoring, under normal traffic. The section, instrumented with strain gages, temperature probes and geophones, has been monitored continuously during 18 months. Signal sorting procedures have been developed for reducing the quantity of recorded data, and for analysing the structural response of the pavement, under highly variable loading conditions. The results of the strain gage measurements, made at different depths within the pavement, have shown that the response of the pavement presents large variations with temperature, and in particular, that the degree of bonding between layers can decreases at high temperatures, leading to sliding between pavement layers. The mechanical response of this section has been analysed using a classical multi-layer linear elastic pavement model and also a viscoelastic model. The best predictions have been achieved with the viscoelastic model. Different approaches for describing the behaviour of pavement layer interfaces have also been evaluated.

The paper presents tests performed on an instrumented motorway section, to monitor traffic and pavement deflections using geophones. Geophones are sensors used to measure displacement velocities, and by integrating their signal, it is possible to monitor vertical displacements. In this study, 4 geophones have been installed in the base layer of the pavement, and their measurements have been recorded under real traffic, during a period of approximately 18 months, using a remote control data acquisition system, transferring the data to a server. Different methods of treatment of the geophone measurements have been proposed: the first application concerns the detection of different heavy vehicle silhouettes, by analysing the number of peaks of the displacement signals; the second application concerns the measurement of vehicle speeds, by determining the time difference between the measurements of two geophones. The third application concerns the measurement of pavement deflections. To measure accurately the deflection, a procedure has been developed, to correct the geophone response, which is attenuated in the low frequency range. This procedure has been validated by measurements under controlled loading conditions, on the IFSTTAR accelerated pavement testing facility, and then applied to in situ measurements. In conclusion, the study shows that geophones, which present the advantage of being relatively inexpensive and robust sensors, offer interesting possibilities for pavement monitoring.

Pavement instrumentation with embeddable in-situ sensors has been a feasible approach to determine pavement deteriorations. Determining pavement deflections during the passage of the load is a promising strategy to determine the overall performance of the pavement. There are different devices that apply loads to the pavements and measure the deflection basin, these include static, vibratory, or impulse loadings. Most commonly used are the static loading like Benkelman beam and impulse loading like the Falling Weight Deflectometer (FWD). However, these techniques are costly and the measurements are recorded infrequently, i.e., once per year or two years. This study focuses on the use of geophones and accelerometers to measure the surface deflections under traffic loading. To develop a method to measure pavement deflections, the sensors were submitted first to laboratory tests, and then tested in situ, in a full scale accelerated pavement test. In the laboratory, the sensors were submitted to different types of loading using a vibrating table. These tests were used to determine the noise and sensitivity of the sensors, and then to evaluate their response to signals simulating pavement deflections under heavy vehicles. The sensor response was compared with measurements of a reference displacement sensor. Different processing techniques were proposed to correct the measurements from geophones and accelerometers, in order to obtain reliable deflection values. Then, the sensors were evaluated in a full scale accelerated test, under real heavy axle loads. Tests were performed at different loads and speeds, and the deflection measurements were compared with a reference anchored deflection sensor. The main advantage of using accelerometers or geophones embedded in the pavement is to enable continuous pavement monitoring, under real traffic. The sensor measurements could also be used to determine the type of vehicles and their corresponding speeds. The study describes in detail the signal analysis needed to measure the pavement deflections accurately. The measurements of pavement deflection can be then used to analyze the pavement behavior in the field, and its evolution with time, and to back-calculate pavement layer properties.