The possibility of wastewater treatment and electricity production using a microbial fuel cell with Cu–B alloy as the cathode catalyst is presented in this paper. Our research covered the catalyst preparation; measurements of the electroless potential of electrodes with the Cu–B catalyst, measurements of the influence of anodic charge on the catalytic activity of the Cu–B alloy, electricity production in a microbial fuel cell (with a Cu–B cathode), and a comparison of changes in the concentration of chemical oxygen demand (COD), NH4+, and NO3– in three reactors: one excluding aeration, one with aeration, and during microbial fuel cell operation (with a Cu–B cathode). During the experiments, electricity production equal to 0.21–0.35 mA·cm−2 was obtained. The use of a microbial fuel cell (MFC) with Cu–B offers a similar reduction time for COD to that resulting from the application of aeration. The measured reduction of NH4+ was unchanged when compared with cases employing MFCs, and it was found that effectiveness of about 90% can be achieved for NO3– reduction. From the results of this study, we conclude that Cu–B can be employed to play the role of a cathode catalyst in applications of microbial fuel cells employed for wastewater treatment and the production of electricity.
Wastewater originating from the yeast industry is characterized by high concentration of pollutants that need to be reduced before the sludge can be applied, for instance, for fertilization of croplands. As a result of the special requirements associated with the characteristics of this production, huge amounts of wastewater are generated. A microbial fuel cell (MFC) forms a device that can apply wastewater as a fuel. MFC is capable of performing two functions at the same time: wastewater treatment and electricity production. The function of MFC is the production of electricity during bacterial digestion (wastewater treatment). This paper analyzes the possibility of applying yeast wastewater to play the function of a MFC (with Ni–Co cathode). The study was conducted on industrial wastewater from a sewage treatment plant in a factory that processes yeast sewage. The Ni–Co alloy was prepared by application of electrochemical method on a mesh electrode. The results demonstrated that the use of MFC coupled with a Ni–Co cathode led to a reduction in chemical oxygen demand (COD) by 90% during a period that was similar to the time taken for reduction in COD in a reactor with aeration. The power obtained in the MFC was 6.1 mW, whereas the volume of energy obtained during the operation of the cell (20 days) was 1.27 Wh. Although these values are small, the study found that this process can offer an additional level of wastewater treatment as a huge amount of sewage is generated in the process. This would provide an initial reduction in COD (and save the energy needed to aerate wastewater) as well as offer the means to generate electricity.
Research related to measurements of electricity production was combined with parallel wastewater parameter reduction in a membrane-less microbial fuel cell (ML-MFC) fed with industry process wastewater (from a yeast factory). Electrodes with Ni–Co and Cu–B catalysts were used as cathodes. A carbon electrode (carbon cloth) was used as a reference due to its widespread use. It was demonstrated that all analyzed electrodes could be employed as cathodes in ML-MFC fed with process wastewater from yeast production. Electricity measurements during ML-MFC operations indicated that power (6.19 mW) and current density (0.38 mA·cm−2) were the highest for Ni–Co electrodes. In addition, during the exploitation of ML-MFC, it was recorded that the chemical oxygen demand (COD) removal per time for all types of electrodes was similar to the duration of COD decrease in the conditions for wastewater aeration. However, the COD reduction curve for aeration took the most favorable course. The concentration of NH4+ in ML-MFC remained virtually constant throughout the measurement period, whereas NO3− levels indicated almost complete removal (with a minimum increase in the last days of cell exploitation).
Microbial fuel cells (MFCs) are devices than can contribute to the development of new technologies using renewable energy sources or waste products for energy production. Moreover, MFCs can realize wastewater pre-treatment, e.g., reduction of the chemical oxygen demand (COD). This research covered preparation and analysis of a catalyst and measurements of changes in the concentration of COD in the MFC with a Ni–Co cathode. Analysis of the catalyst included measurements of the electroless potential of Ni–Co electrodes oxidized for 1–10 h, and the influence of anodic charge on the catalytic activity of the Ni–Co alloy (for four alloys: 15, 25, 50, and 75% concentration of Co). For the Ni–Co alloy containing 15% of Co oxidized for 8 h, after the third anodic charge the best catalytic parameters was obtained. During the MFC operation, it was noted that the COD reduction time (to 90% efficiency) was similar to the reduction time during wastewater aeration. However, the characteristic of the aeration curve was preferred to the curve obtained during the MFC operation. The electricity measurements during the MFC operation showed that power equal to 7.19 mW was obtained (at a current density of 0.47 mA·cm−2).
A huge amount of organic waste is generated annually around the globe. The main sources of solid and liquid organic waste are municipalities and canning and food industries. Most of it is disposed of in an environmentally unfriendly way since none of the modern recycling technologies can cope with such immense volumes of waste. Microbiological and biotechnological approaches are extremely promising for solving this environmental problem. Moreover, organic waste can serve as the substrate to obtain alternative energy, such as biohydrogen (H2) and biomethane (CH4). This work aimed to design and test new technology for the degradation of food waste, coupled with biohydrogen and biomethane production, as well as liquid organic leachate purification. The effective treatment of waste was achieved due to the application of the specific granular microbial preparation. Microbiological and physicochemical methods were used to measure the fermentation parameters. As a result, a four-module direct flow installation efficiently couples spatial succession of anaerobic and aerobic bacteria with other micro- and macroorganisms to simultaneously recycle organic waste, remediate the resulting leachate, and generate biogas.
Wastewater has high potential as an energy source. Therefore, it is important to recover even the smallest part of this energy, e.g., in microbial fuel cells (MFCs). The obtained electricity production depends on the process rate of the electrodes. In MFC, the microorganisms are the catalyst, and the cathode is usually made of carbon material (e.g., with the addition of Pt). To increase the MFC efficiency (and reduce costs by reducing use of the noble metals), it is necessary to search the new cathode materials. In this work, the electricity production from yeast wastewater in membrane-less microbial fuel cells with Cu-Ag cathode was analyzed. In the first place, the measurements of the stationary potential of the electrodes (with Cu-Ag catalyst obtained by the electrochemical deposition technique) were performed. Because the cathode is constantly oxidized during the operation of ML-MFC, it was necessary to pre-oxidize the cathodes. Without pre-oxidation, there is a risk of changing the catalytic properties of the electrodes (along with the level of oxidation of the cathodes’ surface) throughout their operation in the ML-MFC. These measurements allowed to assess the oxidation activity of the Cu-Ag cathodes. Additionally, the influence of anodic charge on the catalytic activity of the Cu-Ag cathodes was measured. Next, the analysis of the electric energy production during the operation of the membrane-less microbial fuel cell (ML-MFC) fed by process yeast wastewater was performed. The highest parameters (the power of 6.38 mW and the cell voltage of 1.09 V) were obtained for a Cu-Ag catalyst with 5% of Ag, which was oxidized over 6 h, and after 3 anodic charges. This research proved that it is feasible to obtain the bio-electricity in the ML-MFC with Cu-Ag cathode (fed by yeast wastewater).