Yusha Li

Dr. Yusha Li

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 November 2020 in Metals
Verified
Journal Article
Open access
PDF file
GLGuangbin Li
Guangbin Li
YLYanhong Liu
Yanhong Liu
YZYingchun Zhang
Yingchun Zhang
HLHuailin Li
Huailin Li
XWXiaojing Wang
Xiaojing Wang
YLYusha Li
Yusha Li
A dense and uniform Cr coating was fabricated on the zirconium alloys fuel claddings by radio frequency (RF) magnetron sputtering to improve the mechanical and anti-oxidation properties under 1200 °C steam environment. The phase composition and the micro and macro morphologies of the specimens were investigated by X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), scanning electron microscope (SEM) and optical-microtopography (OM) analyses, and the high-temperature oxidation behavior was evaluated at 1200 °C steam environment for 3000 s. In this paper, there exists a positive correlation between thickness and Vickers hardness (HV), and a negative correlation between surface roughness and bonding force. Radial tensile was introduced to investigate the deformation-resistant performance, and the displacement of the Cr-coated specimen was as low as 2.32 mm, which was much lower than the uncoated zircaloy cladding (3.05 mm). Different thicknesses of Cr coatings were deposited to investigate the oxidation degrees of zircaloy cladding under a high-temperature steam environment. The optimal 6 μm Cr-coated zirconium alloys cladding exhibited an excellent anti-oxidation property, and the weight gain was as low as ~4.12 mg/cm2, which was almost one-third of the uncoated specimen.

20 November 2024 in Coatings
Verified
Journal Article
Open access
PDF file
YLYusha Li
Yusha Li
XDXiaoxu Dong
Xiaoxu Dong
QLQing Liu
Qing Liu
YYYajie You
Yajie You
ZGZeyu Gao
Zeyu Gao
YZYingchun Zhang
Yingchun Zhang
The pulsed current electrodeposition method was employed for the first time to achieve tungsten coating with a thickness of 433.72 μm on a CuCrZr alloy from Na2WO4-WO3-KCl-NaF molten salt. The microstructure of the coating was observed and the coating density, porosity, hardness, bonding strength, residual stress and oxygen content were tested. The results revealed that the tungsten coating exhibited desirable characteristics such as high density, absence of impurities, excellent adhesion to the matrix (53.16 MPa), residual compressive stress as surface stress, and good stability and durability. Moreover, this thick tungsten coating possesses high density and hardness, low oxygen content and porosity. This offers a novel solution to solve the challenging issue of the connection between tungsten material and heat sink material.

21 February 2025 in Coatings
Verified
Journal Article
Open access
PDF file
XDXiaoxu Dong
Xiaoxu Dong
YLYusha Li
Yusha Li
YYYajie You
Yajie You
ZGZeyu Gao
Zeyu Gao
YZYingchun Zhang
Yingchun Zhang
Characteristics of electrodeposited tungsten coatings prepared at 1193 K and varying current density were investigated. The crystal structure and microstructure of tungsten coatings were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and photoelectron spectroscopy (XPS). The results indicated that pulsed current density significantly influence the tungsten nucleation and electro-crystallization phenomena. The average grain size of the coating becomes larger with increasing current density, which demonstrates that appropriate high cathodic current density can accelerate the growth of grains on the surface of the substrate. The micro-hardness of tungsten coatings increases with increasing thickness and then slightly decreases; the maximum micro-hardness is 589.55 HV, with the oxygen content remaining below 0.03 wt%.

17 October 2025 in Coatings
Verified
Journal Article
Open access
PDF file
XDXiaoxu Dong
Xiaoxu Dong
WLWenqi Liu
Wenqi Liu
YLYusha Li
Yusha Li
ZGZeyu Gao
Zeyu Gao
YZYingchun Zhang
Yingchun Zhang
To address the issue in the pure oxide molten salt system Na2WO4-WO3, where the relatively high melting temperature often causes thermal corrosion of the base material and reduces electrodeposition efficiency. A new molten salt system for electrodeposition tungsten coatings on CuCrZr substrates at relatively low temperatures was investigated. The crystal structure and microstructure of the tungsten coatings were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). The results indicate that the power supply mode, current density, and duty cycle significantly affect the microstructure, crystalline characteristics, and overall performance of the tungsten coating. Pure tungsten coatings were successfully fabricated on CuCrZr substrates at 943 K. The best electrodeposition parameters were determined to be a current density of 40 mA/cm2 and a duty cycle of 40%. Moreover, after prolonged electrodeposition (60 h), the tungsten coatings retained fine grains, with sizes ranging from 2 μm to 6 μm.

1 October 2023 in Journal of Wuhan University of Technology-Mater. Sci. Ed.
Verified
Journal Article
Closed access
PDF file
YLYusha Li
Yusha Li
YZYingchun Zhang
Yingchun Zhang
YLYanhong Liu
Yanhong Liu
GLGuangbin Li
Guangbin Li
XDXiaoxun Dong
Xiaoxun Dong

23 April 2026 in Coatings
Verified
Journal Article
Open access
PDF file
XDXiaoxu Dong
Xiaoxu Dong
YLYusha Li
Yusha Li
WLWenqi Liu
Wenqi Liu
ZGZeyu Gao
Zeyu Gao
YZYingchun Zhang
Yingchun Zhang
Molten salt electrodeposition is a promising technique to prepare high-performance tungsten coatings for fusion reactor first-wall components. However, the ultra-high temperature during deposition causes severe grain coarsening and precipitate dissolution in CuCrZr alloy substrates, resulting in dramatic mechanical property degradation. In this study, a thermal cycle at 1223.15 K for 100 h was employed to simulate the thermal impact of molten salt tungsten electrodeposition (MSE) on CuCrZr alloys, and an aging treatment (703.15 K for 12 h) was adopted to restore the degraded mechanical properties. After aging, the tensile strength and yield strength recovered to 378.35 ± 7.40 MPa and 261.02 ± 3.40 MPa, meeting the minimum tensile property requirements of ITER for CuCrZr alloys. The recovery is attributed to nano-sized Cr-rich phase precipitation and high-density dislocations, providing effective Orowan precipitation strengthening. This work provides the first simple, engineering-friendly post-treatment to repair performance degradation of CuCrZr under the extreme thermal exposure of molten salt electrodeposition, which is critical for large-scale fabrication of high-performance plasma-facing components (PFCs) for fusion reactors.