High-temperature superconducting tapes provide new materials for various high-current applications. The stacked tape cable (STC) is one of the promissing structure, which is based on the idea to stack single REBCO tapes. However, stacking the tapes increases the thickness of the cable and reduces its bending performance. In order to study the bending behavior of stacked tapes, bending tests of single tape was first made to analyze the strain of the REBCO layer at different bending radii, and the strain-current curves were obtained by empirical equations. The cables were stacked in both back-to-back and face-to-face modes. The strains of the REBCO layers in the tapes are calculated, and the critical currents of the cables are experimentally measured at various bending radii. The bending characteristics of the cable are analyzed using the fitted equation, and the experimental results demonstrate good agreement with the calculated results. The results indicate that the REBCO layer exhibits improved bending performance under compression, and thinner cables perform better. Therefore, we added copper tape to adjust the position of the neutral axis to optimize the bending performance. The results show that this method can effectively reduce the bending radius of the stacked cable.
17 March 2025 in Superconductor Science and Technology
Twisted stacked-tape cable in conduit conductor (TSTC-CICC) structures are highly promising due to their ease of fabrication, flexibility, and high current density. In practical applications, the tapes within the conductor experience a combination of torsion and bending, which directly influence their mechanical integrity and electrical performance. This study investigates the mechanical behavior of stacked REBCO tapes in a 6-slot TSTC-CICC, focusing on stress and strain responses under varying twist pitches and bending radii. A shell element-based REBCO tape composite model was developed, and both experimental tests and finite element analyses were conducted to evaluate the mechanical response of the tapes under torsional and bending loads. In the experimental phase, conductor samples with twist pitches of 200 mm and 300 mm were fabricated to examine the onset of mechanical degradation under torsion-bending conditions. The sample with a 200 mm twist pitch showed critical current degradation at a bending radius of 700 mm, while the sample with a 300 mm twist pitch exhibited similar degradation at 900 mm. A finite element analysis method was developed to simulate 3D stacked REBCO tapes under torsion-bending conditions. For computational efficiency, the tapes were simplified into a shell structure. The simulation results revealed that axial strain distribution at critical current degradation points was consistent across different twist pitches and bending radii, closely aligning with experimental findings. The simulation and experimental results suggest that relative sliding between tapes plays a key role in mitigating stress concentration, potentially improving the longevity and performance of the TSTC-CICC in practical applications.
Stacking tapes is one of the methods to increase the transport current of a superconducting cable. A three-slot cable (TSC) by using twisted stacked YBCO tapes is presented in this article. The YBCO tapes embedded in the slot generate an axial strain. Excessive strain leads to a degradation of the critical current. The strain equation is used to obtain the critical twist pitch, which is verified by embedding the tapes into some formers with different twist pitches. For a cable with a diameter of 6 mm and a YBCO tape width of 3 mm, the calculated critical twist pitch is about to 86 mm, which is consistent with the experimental result. Since the magnetic field generated by the stacked tapes causes critical current degradation, the Kim model is used to investigate the critical current of the proposed TSC. Calculation results for different stacking thicknesses compared with experimental results, the maximum error is found to be about 6%. In this article, the critical current of TSC cable is investigated to provide data for future applications of twisting multiple TSC cables to make cable-in-conduit conductors for a high magnetic field and high-current scenarios.
Embedding stacked HTS tapes into twisted slots is one design approach for constructing fusion conductors. This paper adopts a Cable-in-Conduit Conductor (CICC) structure, utilizing commercially REBCO coated conductors. The cable framework is made of copper and features six helically twisted slots filled with 2G HTS tapes. Two 1 m long samples with twist pitches of 200 mm and 300 mm, respectively, were fabricated. In one slot, copper and superconducting tapes were alternated, while the remaining grooves were filled with copper tapes. The 90 µm thick copper-plated bare tapes provided by Shanghai Superconductor were used for testing. By measuring the critical current of tapes positioned at different locations within the grooves at 77 K, the characteristics of each tape in the stacked arrangement were individually characterized. The study obtained the current degradation patterns of tapes located at different positions within the grooves under various bending radii. This paper will present and discuss the preliminary results of the bending measurements conducted at 77 K under a self-field.
12 March 2026 in Superconductor Science and Technology
This paper presents the full-process fabrication and validation of a 16-meter-long, six-slot REBCO Twisted Stacked-Tape Cable-in-Conduit Conductor (TSTC-CICC), a significant step toward compact, high-field fusion magnets. The conductor design incorporates a copper core with helical slots containing stacks of REBCO tapes, with vacuum pressure impregnation (VPI) of solder employed to achieve superior structural integrity and electrical stabilization. Characterization at 77 K demonstrated exceptional longitudinal uniformity in critical current, with a maximum deviation of 5\% and an average n-value of 15, indicating no performance degradation from the bending and impregnation processes. Experimental data were used to validate a finite-element H-formulation model, which subsequently predicts an engineering current density of 228.387 A/mm^2 at 80 kA under operational conditions of 20 K and 20 T. These findings confirm the viability of both the proposed TSTC-CICC architecture and the VPI process for long-length HTS conductors, thereby underpinning their future engineering application in next-generation fusion devices.