Summary: The main approach to managing the volume of sediment transported by stony debris flows routing along channels is through retention basins and open check dams, usually built in the lower reach just upstream of inhabited areas where slopes are gentler. In some cases, these measures are not sufficient to retain all the volume of sediment transported by debris flows. Works for trapping the sediments should also be placed in the upper reach of debris‐flow channels. In this area, where the channel bed is characterized by very high slopes and vertical variability over time, constructing and maintaining transversal embankments for sediment retention is difficult. In addition, they could also be susceptible to failure, potentially increasing the magnitude of the phenomenon instead of mitigating it. On the other hand, other types of works, such as solid‐body check dams or net barriers, have a decreasing efficiency over time in reducing the volume of sediment transported by debris flows. An alternative solution could be a retention basin open on the downstream side, that is, without the ending transversal embankment or berm. Therefore, it can be designated as a deposition area because the retention effect of the downstream embankment is missing, and sediment deposition only occurs due to the flatness of the basin. For sizing purposes, here, we derive two relationships between the deposition area and the volume of the deposit. These two relationships are derived from a physically based geometrical approach and empirical approach, respectively. After analyzing the morphology of the depositional processes that occurred in an existing deposition area during debris‐flow events, we test the validity of the two relationships. Overall, these can be used independently or in combination for designing a deposition area. At last, we introduce the necessary geomorphological conditions for the construction of the deposition area and guidance for its placement.
In the Dolomites, steep rocky cliffs are marked by numerous narrow gullies. When high‐intensity short‐duration precipitation occurs, these gullies concentrate and direct surface runoff to the screes at the foot of rock cliffs. Surface runoff mixes with loose sediments, creating a solid‐liquid surge that, as it moves downhill, increases its volume entraining debris material and transforms into a granular debris flow. Given the ongoing challenge of modeling the relationship between intense rainfall, surface runoff, and debris flow initiation, we take advantage of data from three monitoring stations operating in distinct debris flow active catchments in our study area to make progress. These stations, strategically positioned close to debris flows initiation zones, record videos and different types of flow‐stage data, helping us pinpoint the timing and form of incoming discharge hydrographs. Over a 15‐year period of observation, we collected a comprehensive data set on runoff and mass movement in these catchments, offering valuable insights into their hydrological behavior and the initiation of granular debris flows. To compute infiltration excess runoff generation, we refined an already existing hydrological model and calibrated it using discharge measured at one of the monitoring stations. Testing this updated model against observations from two other larger debris flow sites showed that it can reproduce the initial phases of a debris flow, when sediment concentration rapidly rises. These findings suggest that a well‐tuned hydrological model can predict the discharge from intense, short rainfall events that typically trigger debris flows, as well as the early stages of these phenomena.
Stony debris flows originating from the two basins of Jaron di Sacomedan and Jaron dei Ross pose a significant threat to the inhabited area of Chiapuzza (Dolomites, Northeastern Italian Alps) and the national road SS 51. In the upper part of the Jaron dei Ross basin, a large scree at the foot of a rocky amphitheater undergoes morphological changes due to frequent rockfalls. Previous mitigation efforts have proven inadequate, and after identifying the causes of their failure, new control measures are being planned. These works aim to direct debris flows towards a deposition area capable of intercepting flows from both the Jaron dei Ross and Jaron di Sacomedan basins. Essentially, the upper works in the Jaron dei Ross basin divert debris flows away from the populated area and channel them to a location where the sediment volume transported by debris flows from both basins can be stored. This solution is designed to protect both the Chiapuzza community and the SS51 national road.
Landslides and debris flows are significant disasters that frequently occur on hillslopes, often resulting in casualties and property damage when they take place near residential areas. Specifically, in regions with dams or reservoirs, landslides and debris flows can raise the top of dead storage, reducing the effective storage capacity of these facilities. Additionally, debris flows entering reservoirs can generate tsunami-type waves, potentially leading to overflow-induced flooding and the collapse of hydraulic structures. Numerical modeling has been widely employed to mitigate such disasters. However, most studies utilized three-dimensional hydrodynamics or smoothed particle hydrodynamics, focusing primarily on laboratory-scale events without considering critical processes such as erosion, entrainment, and deposition. These processes are essential for accurately simulating debris flow dynamics. To address these limitations, this study developed a multi-layer dynamics simulation model based on shallow water equations that consider erosion, entrainment, and deposition mechanics, enabling the analysis of field-scale events. The model's performance was validated through theoretical and laboratory experiments. The 2020 Sanyang Reservoir collapse event in South Korea was selected as a case study to evaluate the model's applicability. Scenario-based analyses were conducted, considering debris flow characteristics and reservoir water level conditions, to explore various potential outcomes. The results highlighted the correlation between debris flow momentum and wave scale, with the maximum momentum of the debris flow identified as a strong predictor of the wave's magnitude.
In the Dolomites area, steep rocky cliffs are incised by several chutes that concentrate runoff and deliver it to the scree at their base. This interaction prompts erosive actions, creating channels for debris flows. After intense, short-lasting rainfall, the resulting runoff carries a significant amount of loose debris, forming a solid-liquid surge. This surging flow entrains boulders, gravel, and sand along its path, transforming into an increasingly substantial stony debris flow. To explore how headwater rocky catchments respond hydrologically and trigger stony debris flows, we utilize data gathered from three monitoring stations placed in distinct debris-flow catchments. These stations, located in the debris-flow initiation area of the basins, capture videos and flow-stage data, enabling us to observe the timing and type of the incoming flows. Over 15 years of monitoring, numerous instances of runoff and mass-transport phenomena have been documented. This comprehensive dataset is precious for analyzing the hydrological behavior of small, steep headwater basins and investigating stony debris flow initiation. An existing hydrological model has been partially reformulated, and its updated version was calibrated using the hydrographs measured via a sharp-crested weir. Testing this updated model against observations from two larger debris-flow catchments affirms its capability to replicate the initial phases of a debris flow, particularly when the sediment concentration is quickly increasing. Moreover, combining simulated runoff volume with the entrained sediment volume in the Rovina di Cancia catchment, estimated through DEM of Differences for the debris-flow events that occurred from 2009 to 2022, provides values for solid concentration suitable for predicting sediment volumes carried by debris flows.
Usual works for the reduction of the sediment volume transported by debris flows are the retention basins. Retention basins are usually built on the intermediate and low-sloping reaches of the debris-flow channels or at their end, where the terrain slope is usually not high. When the space required for trapping all the sediment volume is not available or the upper part of the basin must be protected deposition areas can be used. The deposition area is a retention basin without the downstream berm, to be placed in the high-sloping reach of a debris-flow channel. Therefore, it is proposed an approach for the progressive reduction of the sediment volume transported by debris flow: an in-series combination of deposition areas in the high-sloping reaches of the channel, and retention basins in the intermediate low-sloping reaches of the flow path.An application of such approach is shown for the design of the control works on Ru Secco Creek at the purpose of defending the resort area and the village of San Vito di Cadore (Northeast Italian Alps).