Over the years, significant validation work for the neutronics code MPACT has been performed against zero-power critical benchmarks and measured data from operating nuclear power plants. Among all of these efforts, however, validation of the pin-resolved capability in MPACT has been limited by the public availability of experimental data and to a lesser degree availability of measurement techniques and facilities that provide such detailed data. Recently, new measurement results to experimentally determine the reaction rate along the pellet radius from the IPEN/MB-01 research reactor facility (IPEN) have been published as a benchmark in the International Reactor Physics Experiment Project handbook. In this paper, we examine MPACT simulation results for several IPEN benchmark experiments with emphasis on the intrapin reaction rate measurements. The IPEN critical experiments with variations in system temperature and gadolinium loadings are modeled first with the latest MPACT cross-section library and linear source (LS) method of characteristics (MOC) capability. The MPACT results of two-dimensional (2-D) models with axial buckling are within 160 pcm from the experimental eigenvalues using the flat source MOC. Using the LS MOC, the errors are no more than 70 pcm, and the temperature trend of various cases is smaller. The MPACT three-dimensional models with LS show slightly worse comparisons than the 2-D models, which may be due to the isotropic transverse leakage and homogenized cross-section approximations of the 2-D/one-dimensional solver. For the reaction rate validation, MPACT produces intrapin reaction rate results within 2σ of the experiment and shows excellent agreement with the Monte Carlo solution. The observed discrepancies between the simulated results and experiment for the fission rate measurements are discussed. The kinetics parameters measured in another IPEN experiment are also compared with MPACT simulations using different kinetics data sources. According to the validation results, JENDL-4.0 and Santamarina et al.’s data are recommended for MPACT transient calculations.
The default energy deposition model in the CASL neutronics code MPACT assumes all fission energy is deposited locally in fuel rods. Furthermore, equilibrium delayed energy release is assumed for both steady-state and transient calculations. These approximations limit the accurate representation of the heat generation distribution in space and its variations over time, which are essential for power distribution and thermal-hydraulic coupling calculations. In this paper, an improved energy deposition model is presented in both the spatial and time domains. Spatially, the energy deposition through fission, neutron capture, and slowing-down reactions are explicitly modeled to account for the heat generation from all regions of a reactor core, and a gamma smearing scheme is developed that utilizes the gamma sources from neutron fission and capture. In the time domain, the delayed energy release is modeled by solving an additional equation of delayed heat emitters, similar to the equation of delayed neutron precursors. To allow the explicit heat generation coupling, the interfaces between MPACT and CTF were updated to transfer separate heat sources for different material regions (fuel, clad, moderator and guide tube). The results show that the distributions of the energy deposition between MPACT and MCNP agree very well for various 2-D assembly and quarter-core problems without TH feedback. The MPACT/CTF coupled calculation for the hot full power quarter-core case exhibited a reduced peak pin power by 2.3% and a reduced peak fuel centerline temperature by 17 K when using the explicit energy deposition and heat transfer. The new model also shows a maximum 100 pcm keffeffect on assembly depletion problems and an increased overall energy release by 7% in a PWR reactivity-initiated accident (RIA) problem.
This paper presents the most recent progress on the development of gamma transport capability for the CASL neutronics code MPACT: (1) 3D gamma transport and (2) explicit gamma heating capabilities. The 3D gamma calculation capability was implemented by leveraging the 2D/1D solver originally developed for neutron calculations. The results were verified by MCNP6 on a small assembly with 5 × 5 pins. Generally, errors were lower than 0.5% on each axial mesh as long as MPACT was running with enough axial meshes. The gamma heating calculation considered the energy deposition from photoelectric absorption, Compton scattering, and pair production. Verification with MCNP6 for both 2D and 3D benchmarks showed that the errors of energy depositions are comparable with those of gamma fluxes, proving the proper implementation of the energy deposition.