Highly selective plasma etching of silicon nitride (Si3N4), while not etching silicon dioxide (SiO2), is a critical step in the fabrication of microelectronics devices. In many applications, this etching must be damage-free and isotropic, which then motivates the use of remote plasmas where the reactants interacting with the substrate are dominantly neutral species. In this paper and Paper II, mechanisms for highly selective Si3N4 etching in remote plasmas are discussed based on results from experiments and simulations. It has been shown experimentally that high Si3N4/SiO2 etch selectivity (≈380) can be achieved in the downstream effluent of an NF3/N2/O2/H2 plasma. The authors found that H2 plays a principal role in the reaction mechanism as Si3N4/SiO2 selectivity shows a sharp maximum as a function of the H2 flow rate. Based on this observation, and measured densities of F-atoms and H2 in the process chamber, a mechanism of selective Si3N4/SiO2 etching is proposed in which HF molecules in vibrationally excited states accelerate etching reactions. A reaction mechanism for NF3/N2/O2/H2 plasmas and its afterglow was developed to computationally determine the species densities and fluxes on the wafer level, validated by comparing with experimentally measured F-atom and H2 densities. The calculated species densities and fluxes were used as input to an analytical model of Si3N4 and SiO2 etching based on the results of quantum chemistry simulations. This paper presents experimental results (etching data and species densities), the reaction mechanism for NF3/N2/O2/H2 plasmas, and the results of simulations of gas phase chemistry. Quantum chemistry simulations of elementary etching reactions, description of the analytical model of Si3N4 and SiO2 etching, calculations of the etch rates, and Si3N4/SiO2 selectivity with this model are presented in Paper II.
18 November 2024 in Journal of Vacuum Science & Technology A
Etching of high aspect ratio features into alternating SiO2 and SiN layers is an enabling technology for the manufacturing of 3D NAND flash memories. In this paper, we study a low-temperature or cryo plasma etch process, which utilizes HF gas together with other gas additives. Compared with a low-temperature process that uses separate fluorine and hydrogen gases, the etching rate of the SiO2/SiN stack doubles. Both materials etch faster with this so-called second generation cryo etch process. Pure HF plasma enhances the SiN etching rate, while SiO2 requires an additional fluorine source such as PF3 to etch meaningfully. The insertion of H2O plasma steps into the second generation cryo etch process boosts the SiN etching rate by a factor of 2.4, while SiO2 etches only 1.3 times faster. We observe a rate enhancing effect of H2O coadsorption in thermal etching experiments of SiN with HF. Ammonium fluorosilicate (AFS) plays a salient role in etching of SiN with HF with and without plasma. AFS appears weakened in the presence of H2O. Density functional theory calculations confirm the reduction of the bonding energy when NH4F in AFS is replaced by H2O.
29 January 2020 in Journal of Vacuum Science & Technology A
Developing processes for highly selective etching of silicon nitride (Si3N4) with respect to silicon dioxide (SiO2) is a major priority for semiconductor fabrication processing. In this paper and in Paper I [Volynets et al., J. Vac. Sci. Technol. A 38, 023007 (2020)], mechanisms are discussed for highly selective Si3N4 etching in a remote plasma based on experimental and theoretical investigations. The Si3N4/SiO2 etch selectivity of up to 380 was experimentally produced using a remote plasma sustained in NF3/N2/O2/H2 mixtures. A selectivity strongly depends on the flow rate of H2, an effect attributed to the formation of HF molecules in vibrationally excited states that accelerate etching reactions. Based on experimental measurements and zero-dimensional plasma simulations, an analytical etching model was developed for etch rates as a function of process parameters. Reaction rates and sticking coefficients were provided by quantum chemistry models and also fitted to the experimental results. Etch rates from the analytical model show good agreement with the experimental results and demonstrate why certain etchants accelerate or inhibit the etch process. In particular, the modeling shows the important role of HF molecules in the first vibrationally excited state [HF(v = 1)] in achieving high Si3N4/SiO2 selectivity.
6 October 2017 in Journal of Vacuum Science & Technology A
This paper describes the study of mechanisms of highly selective silicon nitride etching, in particular, the role of NO in silicon nitride etching by atomic fluorine. This paper presents experimental and simulation data about SiN, SiO2, and Si etching with NF3/O2 remote plasma. Quantum chemistry simulations show that NO reacts with the F–N bond in a SiN cluster with lower activation energy than the F-atom. Thus, NO increases the rate of fluorine migration on the silicon nitride surface from the nitrogen atom to the silicon atom during the etching process. In the absence of NO, such migration proceeds with relatively high activation energy, which limits the etching rate. The analytical model based on the SiN etching mechanism taking into account the fluorine migration is proposed. The results of calculations with the analytical model show a good agreement with the experimental SiN, SiO2, and Si etch rates.
31 August 2018 in Journal of Vacuum Science & Technology A
Dry etching of silicon nitride (SiN) is a challenging process in the semiconductor industry and requires high etch selectivity. Fluorine containing chemistry is widely used to etch silicon based materials, and one of the methods to increase the etch selectivity is to use reactants enhancing SiN etching in the presence of atomic fluorine. In this paper, quantum chemistry simulations have been carried out using the density functional theory method [B3LYP, 6-31 + G(d,p)] in order to determine such reactants. These simulations are based on the assumption that such reactants, for example, NO, can increase SiN etch rate via interacting with F–N bonds of the modified SiNFx surface. Silicon nitride cluster with F–N bonds is used here as a model of the modified SiNFx surface. Several new reactants (HF, Cl, H, Br, and FNO) enhancing SiN etch rate have been found by these simulations. The fact that such species as NO, HF, and H atoms can enhance SiN etching explains qualitatively some previously published experimental data.
Chemical functionalization of diamond surfaces by hydrogen is an important method for controlling the charge state of near‐surface fluorescent color centers, an essential process in fabricating devices such as diamond field‐effect transistors and chemical sensors, and a required first step for realizing families of more complex terminations through subsequent chemical processing. In all these cases, termination is typically achieved using hydrogen plasma sources that can etch or damage the diamond, as well as deposited materials or embedded color centers. This work explores alternative methods for lower‐damage hydrogenation of diamond surfaces, specifically the annealing of diamond samples in high‐purity, non‐explosive mixtures of nitrogen and hydrogen gas, and the exposure of samples to microwave hydrogen plasmas in the absence of intentional stage heating. The effectiveness of these methods are characterized by x‐ray photoelectron spectroscopy (XPS), and comparison of the results to density‐functional modelling of the surface hydrogenation energetics implicates surface oxygen ligands as the primary factor limiting the termination quality of annealed samples. Finally, photoluminescence (PL) spectroscopy is used to verify that both the annealing and reduced sample temperature plasma methods are non‐destructive to near‐surface ensembles of nitrogen‐vacancy (NV) centers, in stark contrast to plasma treatments that use heated sample stages.