Soft tissue tumors are rare tumors, and their histological examination remains a challenge. The establishment of the correct initial histopathologic diagnosis is critical. However, due to the rarity of soft tissue and bone tumors and the inherent difficulty of their classification and diagnostics, discrepancies may occur in up to one third of cases. For these reasons, several studies recommend the involvement of experienced pathologists frequently performing sarcoma diagnostics. Until now, there is only scarce information about how long it takes to establish a correct sarcoma diagnosis. We thus analyzed all consecutive patients presented to the Swiss Sarcoma Network Tumor Board (SSN-MDT/SB) with a primary diagnosis of a soft tissue tumor over a 2-year period (01/2019 to 12/2020) based on a tumor biopsy. We then compared the final histopathological diagnosis of two comparable institutions with similar case load, but different workflows: (i) institution A, with an initial diagnosis performed by a local pathologist, and reviewed by a reference pathologist, and (ii) institution B, with the final diagnosis performed directly by a reference pathologist. In addition, we analyzed the time from biopsy to establishment of the diagnosis. A total of 347 cases were analyzed, 196 from institution A, and 149 from institution B. In 77.6% of the cases, the diagnosis from the local pathologist was concordant with the expert review. Minor discrepancies were found in 10.2% of the cases without any consecutive changes in treatment strategy. In the remaining 12.2% of the cases, there were major discrepancies which influenced the treatment strategy directly. Establishing the final report took significantly longer in institution A (4.7 working days) than in institution B (3.3 working days; ). Our results confirm the importance of a pathological second review by a reference pathologist. We recommend direct analysis by experts, as diagnoses can be made more accurately and quickly. Within the SSN, establishing the sarcoma diagnosis is overall accurate and quick but still can be improved.
Since the middle of the 20th century, total hip arthroplasty has become a very successful treatment for all end-stage diseases of the hip joint. Charnley solved with his low frictional torque arthroplasty the problem of wear and friction with the introduction of a new bearing couple and the reduction of the head size, which set the prerequisite for the further development of stem design. This narrative review presents the major developments of regular straight stems in hip arthroplasty. It does not only provide an overview of the history but also assembles the generally scarce documentation available regarding the rationale of developments and illustrates often-unsuspected links. Charnley's success is based on successfully solving the issue of fixation of the prosthetic components to the bone, using bone cement made of polymethyl-methacrylate. In the field of cemented anchorage of the stem, two principles showing good long-term revision rates emerged over the years: the force-closed and the shape-closed principles. The non-cemented anchorage bases on prosthesis models ensure enough primary stability for osteointegration of the implant to occur. For bone to grow onto the surface, not only sufficient primary stability is required but also a suitable surface structure together with a biocompatible prosthetic material is also necessary.
We present a case with bilateral hematogenous hip periprosthetic joint infection with Enterococci which could be treated successfully with implant retention despite chronification and partial loosening. A debridement and replacement of the modular components was carried out with replacement of a loose acetabular cup on the right side. Considering poor local infection control, antibiotic treatment was enhanced by local application of vancomycin. In the present case, treatment of chronic enterococcal periprosthetic joint infection while preserving the implants was successful despite unfavorable odds. Considering the duration of infection, causative microorganism, and loosening of one of the implants, staged exchange of both hip replacements would have been the standard procedure. This case illustrates that some concepts have to be challenged from time to time.
Introduction: Periprosthetic fractures (PPF) of the proximal femur are a leading cause of revision after total hip arthroplasty. Internal fixation may be chosen if the hip implant is stable or if a stable fixation may be obtained. Preservation of bone perfusion and adequate stability are essential for successful fracture healing. As presented, plate design and applica-tion may induce both osteonecrosis and atrophy of the bone. Case Report: An 82-year-old female sustained a PPF of the proximal femur after cemented hemiarthroplasty. The fracture was treated by plate fixation with cerclages applied at the level of the femoral stem. While the fracture healed without loosening of the components, pronounced atrophy of the whole femur developed, with devitalized areas of the bone un-derlying the plate. The plate used had no undercuts and probably had excessive stiffness. Conclusion: When not strictly applied as an internal fixator at a distance from the bone, the plate model used in this case may disturb periosteal blood flow, causing osteonecrosis. Fur-thermore, high bending rigidity of the plate-bone construct may lead to stress shielding and atrophy. Design and mechanical properties of a plate are relevant in fracture healing. Keywords: Periprosthetic fracture, plate fixation, internal fixation, bone biology, bone ne-crosis, plate contact.
"Reply to the Letter to the editor from Grappiolo G et al. to the article ‘The History of the development of the regular straight stem in hip arthroplasty’" published on 01 Feb 2024 by Bioscientifica Ltd.