Traditional conductive materials do not meet the increasing requirements of electronic products because of such materials’ high rigidity, poor flexibility, and slow biodegradation after disposal. Preparing flexible conductive materials with excellent mechanical properties is an active area of research. The key to flexible conductive materials lies in the combination of the polymer matrix and conductive components. This combination can be achieved by making a film of renewable nano-microcrystalline cellulose (NCC) and reduced graphene oxide (rGO) with excellent electrical conductivity—by simple filtration and introducing polyethylene glycol (PEG) to enhance the functionality of the composite film. Graphene imparted conductivity to the composite film, which reached 5.67 S·m⁻¹. A reinforced NCC/rGO/PEG-4 composite film with a thickness of only 21 μm exhibited a tensile strength of 30.56 MPa, which was 83% higher than that of the sample without PEG (16.71 MPa), and toughness of 727.18 kJ·m⁻³, which was about 132% higher than that of the control sample (NCC/rGO, 313.86 kJ·m⁻³). This ultra-thin conductive composite film—which can be prepared simply, consists of environmentally sustainable and biodegradable raw materials, and exhibits excellent mechanical properties—has substantial potential for applications in e.g., flexible electronic wearable devices, electrodes, and capacitors.

The multi-layered and multi-material structures of a violin’s surface varnish film make it more challenging to comprehensively understand the patterns of sound quality changes during the coating process. Using an alcohol varnish coating technique on one or both sides of the wood, along with a combination of micro-morphology, material characterization, and vibration signal processing, this study traced and analyzed the changes in the acoustic vibration properties of Norway spruce wood during the coating process. The results showed that the acoustic characteristics of the coated wood tended to change in an unfavorable direction throughout the coating process, and the specific dynamic elastic modulus (E_sp) of the final single- and double-sided coating varied by −1.77% and −6.07%, respectively. The loss angle tangent (tanδ) had the opposite trend, with rates of change of 20.76% and 30.42%. The sizing and priming treatments in the pretreatment stage had some positive effects on the acoustic properties of the wood specimens. Additionally, significant changes in acoustic vibration performance parameters began to be highlighted at the color paint stage (p < 0.05). These insights provide reference data for the improvement of violin acoustic performance and the simplification of the coating process.

The acoustic vibration performance of wood affects the quality of many musical instruments, and the variability of wood causes obvious differences between individual timber samples. To mitigate the variations among the individual timber samples intended for musical instruments, in this study, we combined finite element simulation with experimental testing to investigate the effect of the periodic annular groove structure on the comprehensive acoustic vibration characteristics of wood. The results revealed that there are discernible correlations between the structural parameters of the periodic annular groove and the key acoustic parameters of wood, including the resonant frequency, equivalent dynamic modulus of elasticity, equivalent specific dynamic modulus of elasticity, equivalent acoustic radiation quality constant, and equivalent acoustic impedance. These relationships can be used to fine-tune the overall acoustic vibration performance of wood and harmonize the acoustic vibration characteristics among different timber specimens. The effects of the periodic annular groove structure on the five acoustic vibration parameters obtained through finite element simulations exhibited minimal differences to the corresponding results from experimental tests. Furthermore, there was a remarkably strong correlation between the outcomes of the finite element simulations and the experimental test results, with the coefficient of determination exceeding 0.99.

The effect of structure on the vibration response was explored for four piano soundboards with different but commonly adopted structures. The vibration response was obtained using the free-vibration method, and the values of the dynamic modulus of elasticity and dynamic shear modulus obtained using the free-vibration frequency method (E_F and G_F) were compared with the dynamic modulus of elasticity obtained using the Euler beam method (E_E) and dynamic shear modulus obtained using the free-plate torsional vibration method (G_T), respectively. It was found that the soundboards with different structures had different vibration modes and that excitation at different locations highlighted different vibration modes. For all the soundboards analyzed, the E_E and G_T were higher than E_F and G_F by 2.2% and 24.3%, respectively. However, the trends of the results of these methods were the same. The four piano soundboards with different structures possessed varying dynamic moduli of elasticity and dynamic shear moduli. These rules are consistent with the grain directions of the soundboards and the anisotropy of the wood (the direction of the units of the soundboards). The results show that the vibration mode of the piano soundboard is complex. The dynamic elastic modulus of the soundboard can be calculated using the Euler beam method. The results provide a reference for studies on the vibration response, material selection, production technology, and testing of piano soundboards.

To address the pollution issues of industrial oily wastewater and catering industry wastewater, a series of Ti₃C₂T_x/TEMPO oxidized cellulose nanofibers composite aerogels with varying Ti₃C₂T_x content were successfully prepared using liquid nitrogen non-directional and directional freezing methods, with Ti₃C₂T_x and TEMPO oxidized cellulose nanofibers (TOCNF) as the main raw materials. The prepared samples were then hydrophobically modified using methyltrichlorosilane (MTCS) via chemical vapor deposition (CVD). The results showed that the directional Ti₃C₂T_x/TOCNF composite aerogel had the most orderly SEM morphology. The hydrophobic Ti₃C₂T_x/TOCNF composite aerogels exhibited efficient adsorption separation capabilities, with an adsorption capacity ranging from 21.5 to 78.2 times their own mass. Notably, the oil absorption performance was optimal when the mass fraction of Ti₃C₂T_x was 33.3%. After five adsorption cycles, the adsorption capacity of M5C10 (with a mass ratio of Ti₃C₂T_x to TOCNF of 5:10) only decreased by around 11%. M5C10 exhibits highly efficient oil absorption performance, which is of considerable significance for the research on oil-water separation treatment of industrial wastewater, domestic wastewater, and sewage from the catering industry.

Resonance boards of Chinese traditional instruments such as the Guzheng and Guqin typically are arched, with the arch height influencing their resonance characteristics. This study focuses on Paulownia wood utilized for resonance boards. The bottom surfaces were thinned in 1 mm increments, with vibration signatures acquired at each reduction stage using a multi-channel FFT analyzer. Subsequently, time-domain characteristic parameters of the signals were extracted through MATLAB-based signal processing. Modal and harmonic response simulations of the structure were conducted using finite element software. The results indicated that variations in arch height affected the frequency spectrum response of the vibrations of Paulownia wood, altering the structural energy radiation levels. Lower arch heights (0–2 mm) had a greater impact on the fundamental frequency. The arch height was 1 mm and 2 mm, with R1,1 and R1,2 being −5.31% and −8.62%, respectively. Skewness and kurtosis were negatively correlated with arch height. When ΔH was 3.06, the radiation effect was optimal. The changes in arch height influenced the vibrational modes and energy distribution of Paulownia. Higher arch heights (3–6 mm) have less effect on the fundamental frequency and impose some constraints on the mode vibration pattern. Furthermore, the results of the frequency-domain and time-domain analyses were found to be largely consistent with the finite element simulation results. The results provide guidance for changing the arch height to modulate the acoustic vibration response of the resonance board, which is of significance for the personalized design of future musical instruments.