Heat sinks are widely used in electronic devices with high heat flux. The design and build of microstructures on heat sinks has shown effectiveness in improving heat dissipation efficiency. In this paper, four kinds of treatment methods were used to make different microstructures on heat sink surfaces, and thermal radiation coating also applied onto the heat sink surfaces to improve thermal radiation. The surface roughness, thermal emissivity and heat dissipation performance with and without thermal radiation coating of the heat sinks were studied. The result shows that with an increase of surface roughness, the thermal emissivity can increase up to 2.5 times. With thermal radiation coating on a surface with microstructures, the heat dissipation was further improved because the heat conduction at the coating and heat sink interface was enhanced. Therefore, surface treatment can improve the heat dissipation performance of the heat sink significantly by enhancing the thermal convection, radiation and conduction.

Oil motion control is the key for the optical performance of electro-fluidic displays (EFD). In this paper, we introduced an extra pinning structure (EPS) into the EFD pixel to control the oil motion inside for the first time. The pinning structure canbe fabricated together with the pixel wall by a one-step lithography process. The effect of the relative location of the EPS in pixels on the oil motion was studied by a series of optoelectronic measurements. EPS showed good control of oil rupture position. The properly located EPS effectively guided the oil contraction direction, significantly accelerated switching on process, and suppressed oil overflow, without declining in aperture ratio. An asymmetrically designed EPS off the diagonal is recommended. This study provides a novel and facile way for oil motion control within an EFD pixel in both direction and timescale.

Electrowetting with a dielectric layer is commonly preferred in practical applications. However, its potential is often limited by factors like the properties of the dielectric layer and its breakdown, along with the complexity of the deposition method. Fortunately, advancements in 3D inkjet printing offer a more adaptable solution for making patterned functional layers. In this study, we used a negative photoresist (HN-1901) to create a new dielectric layer for an electrowetting display on a 3-inch ITO glass using a Dimatix DMP-2580 inkjet printer. The resulting devices performed better due to their enhanced resistance to dielectric breakdown. We meticulously investigated the physical properties of the photoresist material and printer settings to achieve optimal printing. We also controlled the uniformity of the dielectric layer by adjusting ink drop spacing. Compared to traditional electrowetting display devices, those with inkjet-printed dielectric layers showed significantly fewer defects like bubbles and electrode corrosion. They maintained an outstanding response time and breakdown resistance, operating at an open voltage of 20 V. Remarkably, these devices achieved faster response times of ton 22.3 ms and toff 14.2 ms, surpassing the performance of the standard device.

Electrowetting display (EWD) is one of the latest and most promising reflective displays. However, some defects are easily caused in a driving process. For example, the aperture ratio of pixels can be reduced due to oil splitting, and the grayscale cannot be stabilized due to charge trapping. These defects can be effectively solved by designing driving waveforms for EWDs. So, a power function driving waveform was proposed in this paper, which consisted of an oil splitting suppression stage, a direct current (DC) driving stage and an oil stabilization stage. Firstly, the relationships among luminance values, power constants and driving time were measured. An optimal oil splitting suppression stage was obtained, which could effectively inhibit oil splitting. Then, the response time could be reduced by a DC voltage in the DC driving stage. Finally, a voltage slope was tested during the oil stabilization stage, which was used to counteract voltage created by the charge trapping. The experimental results showed that compared with a linear function waveform, the response time could be shortened by 16.1%, and the luminance value could be increased by 3.8%. The aperture ratio and oil stability of EWD can be effectively improved by these findings, thereby increasing its potential application in the display field.

A novel porous nickel–copper composite was designed and fabricated by sintering a mixture of a high-porosity open-cell copper foam plate and fine nickel powder. The microstructure of the porous nickel–copper composite was characterised by the scanning electron microscope. The effects of sintering temperature and dwelling time on the sintering shrinkage, sintered porosity, capillary performance and mechanical properties of the porous composite and monoporous sintered nickel powder were investigated experimentally. The nickel–copper composite presented significant lower sintering shrinkage, higher porosity, lower tensile strength and better capillary performance than the sintered nickel powder under all sintering conditions. The sintering temperature has more influence than the dwelling time on both the capillary performance and tensile strength of the sintered composite.