Obtaining silicon-based photonic-structures in the ultraviolet range would expand the wavelength bandwidth of silicon technology, where it is normally forbidden. Herein, we fabricated porous silicon microcavities by electrochemical etching of alternating high and low refraction index layers; and were carefully subjected to two stages of dry oxidation at 350 °C for 30 minutes and 900 °C, with different oxidation times. In this way, we obtained oxidized porous silicon that induces a shift of a localized mode in the ultraviolet region. The presence of Si-O-Si bonds was made clear by FTIR absorbance spectra. High-quality oxidized microcavities were shown by SEM, where their mechanical stability was clearly visible. We used an effective medium model to predict the refractive index and optical properties of the microcavities. The model can use either two or three components (Si, SiO₂, and air). The latter predicts that the microcavities are made almost completely of SiO₂, implying less photon losses in the structure. The theoretical photonic-bandgap structure and localized photonic mode location showed that the experimental spectral peaks within the UV photonic bandgap are indeed localized modes. These results support that our oxidation process is very advantageous to obtain complex photonic structures in the UV region.

Porous Si-SiO₂ UV microcavities are used to modulate a broad responsivity photodetector (GVGR-T10GD) with a detection range from 300 to 510 nm. The UV microcavity filters modified the responsivity at short wavelengths, while in the visible range the filters only attenuated the responsivity. All microcavities had a localized mode close to 360 nm in the UV-A range, and this meant that porous Si-SiO₂ filters cut off the photodetection range of the photodetector from 300 to 350 nm, where microcavities showed low transmission. In the short-wavelength range, the photons were absorbed and did not contribute to the photocurrent. Therefore, the density of recombination centers was very high, and the photodetector sensitivity with a filter was lower than the photodetector without a filter. The maximum transmission measured at the localized mode (between 356 and 364 nm) was dominant in the UV-A range and enabled the flow of high energy photons. Moreover, the filters favored light transmission with a wavelength from 390 nm to 510 nm, where photons contributed to the photocurrent. Our filters made the photodetector more selective inside the specific UV range of wavelengths. This was a novel result to the best of our knowledge.

In this study, opal–magnetite photocatalysts based on SiO₂ artificial opal crystals infiltrated with different concentrations of Fe₃O₄ nanoparticles (NPs) were synthesized using a combination of lateral infiltration and co-assembly methods. By adjusting the concentration of Fe₃O₄ NPs in the SiO₂ opal crystal, the energy band gap (Eg) was tuned to enable efficient degradation of methylene blue (MB) under visible light (410 nm and 575 nm). The photocatalytic process involved two stages: MB adsorption on the surface due to charge differences in the composite film and subsequent degradation through oxidative radicals on the catalyst’s surface. The developed material exhibited potential for applications in water remediation.

Optical tweezers is an example how to use light to generate a physical force. They have been used to levitate viruses, bacteria, cells, and sub cellular organisms. Nonetheless it would be beneficial to use such force to develop a new kind of applications. However the radiation pressure usually is small to think in moving larger objects. Currently, there is some research investigating novel photonic working principles to generate a higher force. Here, we studied theoretically and experimentally the induction of electromagnetic forces in one-dimensional photonic crystals when light impinges on the off-axis direction. The photonic structure consists of a micro-cavity like structure formed of two one-dimensional photonic crystals made of free-standing porous silicon, separated by a variable air gap and the working wavelength is 633[emsp14]nm. We show experimental evidence of this force when the photonic structure is capable of making auto-oscillations and forced-oscillations. We measured peak displacements and velocities ranging from 2 up to 35 microns and 0.4 up to 2.1[emsp14]mm/s with a power of 13[emsp14]mW. Recent evidence showed that giant resonant light forces could induce average velocity values of 0.45[emsp14]mm/s in microspheres embedded in water with 43[emsp14]mW light power.

In this work, we have followed ethanol evaporation at two different concentrations using a fiber optic spectrometer and a screen capture application with a resolving capacity of 10 ms. The transmission spectra are measured in the visible-near-infrared range with a resolution of 0.5 nm. Porous Silicon microcavities were fabricated by electrochemistry etching of crystalline silicon. The microcavities were designed to have a localized mode at 472 nm (blue band). Ethanol infiltration produces a redshift of approximately 17 nm. After a few minutes, a phase change from liquid to vapor occurs and the localized wavelength shifts back to the blue band. This process happens in a time window of only 60 ms. Our results indicate a difference between two distinct ethanol concentrations (70% and 35%). For the lower ethanol concentration, the blue shift rate process is slower in the first 30 ms and then it equals the high ethanol concentration blue shift rate. We have repeated the same process, but in an extended mode (750 nm), and have obtained similar results. Our results show that these photonic structures and with the spectroscopic technique used here can be implemented as a sensor with sufficient sensitivity and selectivity. Finally, since the photonic structure is a membrane, it can also be used as a transducer. For instance, by placing this photonic structure on top of a fast photodetector whose photo-response lies within the same bandwidth, the optical response can be transferred to an electrical signal.

Each tubulin protein molecule on the cylindrical surface of a microtubule, a fundamental element of the cytoskeleton, acts as a unit cell of a crystal sensor. Electromagnetic sensing enables the 2D surface of microtubule to act as a crystal or a collective electromagnetic signal processing system. We propose a model in which each tubulin dimer acts as the period of a one-dimensional crystal with effective electrical impedance related to its molecular structure. Based on the mathematical crystal theory with one-dimensional translational symmetry, we simulated the electrical transport properties of the signal across the microtubule length and compared it to our single microtubule experimental results. The agreement between theory and experiment suggests that one of the most essential components of any Eukaryotic cell acts as a one-dimensional crystal.