This paper presents a numerical study of the optimization of the geometric parameters of a four-bladed Darrieus vertical-axis wind turbine (VAWT) with a NACA 0021 aerodynamic profile. The aim of the study was to increase the aerodynamic efficiency of the turbine by selecting optimal values of the rotor diameter and blade chord length. The Taguchi method using an orthogonal array was used as an optimization method, which reduced the number of necessary calculations from 77 to 20 while maintaining the reliability of the analysis. CFD modelling was performed in the ANSYS 2022 R2 Fluent software environment based on a two-dimensional non-stationary model, including a full rotor revolution and an analysis of the steady-state mode for the twentieth cycle. As a result of the analysis, the optimal parameters were determined: rotor diameter D = 3 m and chord length c = 0.4 m. Additionally, for the selected configuration, the numerical model was validated by constructing the dependence of the power coefficient Cp on the tip speed ratio λ in the range from 0.2 to 2.8. The maximum value of Cp was 0.35 at λ = 2.2, which is an increase of ~64% compared to the least efficient rotation mode in the considered range of λ. The obtained results allow us to conclude that the Taguchi method can be used in combination with CFD modelling for fast and accurate optimization of the aerodynamic parameters of low-power wind turbines.

In this study, we conducted experimental and numerical investigations of a Darrieus rotor with asymmetrical blades, which has two structural configurations—with and without horizontal parallel plates. Experimental tests were conducted in a wind tunnel at various air flow velocities (ranging from 3 m/s to 15 m/s), measuring rotor rotation frequency, torque, and thrust force. The computational simulation used the ANSYS 2022 R2 Fluent software package, where CFD simulations of air flow around both rotor configurations were performed. The calculations employed the Realizable k-ε turbulence model, while an unstructured mesh with local refinement in the blade–flow interaction zones was used for grid generation. The study results showed that the rotor with horizontal parallel plates exhibits higher aerodynamic efficiency at low wind velocities compared to the no-plates rotor. The experimental findings indicated that at wind speeds of 3–6 m/s, the rotor with plates demonstrates 18–22% higher torque, which facilitates the self-start process and stabilizes turbine operation. The numerical simulations confirmed that horizontal plates contribute to stabilizing the air flow by reducing the intensity of vortex structures behind the blades, thereby decreasing aerodynamic drag and minimizing energy losses. It was also found that the presence of plates creates a directed flow effect, increasing the lift force on the blades and improving the power coefficient (Cp). In the case of the rotor without plates, the CFD simulations identified significant low-pressure zones and high turbulence regions behind the blades, leading to increased aerodynamic losses and reduced efficiency. Thus, the experimental and numerical modeling results confirm that the Darrieus rotor with horizontal parallel plates is a more efficient solution for operation under low and variable wind conditions. The optimized design with plates ensures more stable flow, reduces energy losses, and increases the turbine’s power coefficient. These findings may be useful for designing small-scale wind energy systems intended for areas with low wind speeds.

This paper presents the results of wind tunnel experiments, where lift and drag coefficients were studied at various angles of attack and flow speeds, alongside numerical simulations conducted in ANSYS. The main objectives of this study are to investigate the aerodynamic characteristics and self-starting capabilities of three-bladed Darrieus rotors with asymmetrical blades and assess their efficiency. This study presents results on pressure distribution, velocity contours, and the impact of the angle of attack on pressure and aerodynamic characteristics. The results show that blades with asymmetric shapes achieve maximum values of lift and drag coefficients at angles of attack between 180° and 210°, with peak coefficients of Cx = 1.38 and Cy = 2.84, respectively. These findings indicate high effectiveness of the blades at low wind speeds, making them promising for use in WEIs where good starting characteristics and high power output are especially important. A good correlation was found between experimental data and numerical simulation results. This study contributes to the development of recommendations for optimizing the design and operating parameters of wind-driven powerplants, which in turn can improve their reliability and economic efficiency. Thus, the paper aims to expand the knowledge in the field of wind power engineering and to develop technologies to facilitate a wider adoption of wind-driven powerplants in the energy infrastructure of different regions.