Lightweight aluminum matrix composites with superior strength and structural integrity are in high demand for next-generation transportation and aerospace applications. In this work, Al6060-based composites reinforced with ≈2 wt.% TiB₂ were produced using a hybrid processing route that combines ultrasonically assisted stir casting with radial-shear rolling (RSR). This strategy enabled uniform particle dispersion, strong matrix–reinforcement bonding, and substantial microstructural refinement (grain size 4–6 μm) with reduced porosity. Consequently, the Al6060/TiB₂ composites demonstrated substantial gains over the as-cast alloy, combining a yield strength of 108.6 MPa, ultimate tensile strength of 156.9 MPa, and microhardness of 76.3 HV0.2 with a balanced ductility of ~9%. The demonstrated synergy of ultrasound-assisted casting and severe plastic deformation highlights a scalable pathway for fabricating high-performance aluminum composites, positioning them as promising candidates for aerospace, automotive, and other advanced engineering sectors.

Pure aluminum, due to its inherent low strength and softness, is unsuitable for most structural applications. However, unlike many aluminum alloys, pure aluminum exhibits high ductility and is often free from expensive alloying elements. This makes it a promising candidate for minor reinforcement to produce cost-effective composites with an optimal balance of strength and ductility. This study assesses the possibility of improving the mechanical performance of pure aluminum specimens by minor reinforcement (~0.36 wt. %) with fine B₄C particles and T6 heat treatment. The composites were obtained using ultrasonic-assisted stir casting and were characterized by assessing their density, microhardness, yield strength (YS), ultimate tensile strength (UTS), and elongation. Light microscopy (LM), scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and X-ray diffraction (XRD) tests were conducted to investigate the presence and distribution of reinforcing particles in the Al matrix. Minor reinforcement of ~0.5–2 μm with B₄C particles without/with subsequent T6 heat treatment resulted in an increase in microhardness by 71.45% and 143.37% and UTS by 71.05% and 140.16%, respectively, while the elongation values of the specimens decreased to 51.98% and 42.38%, respectively, compared with the adopted initial matrix Al specimen.

A novel rolling scheme incorporating an inclined oval-caliber configuration is proposed to enhance plastic deformation mechanisms in the traditional oval–round rolling sequence. Finite Element Method (FEM) simulations were performed using DEFORM-3D to evaluate and optimize this new scheme across multiple objectives: maximizing average effective strain, minimizing strain non-uniformity (captured via the standard deviation of effective strain), and minimizing rolling force. Numerical modeling was conducted for calibration angles of γ = 0°, 25°, 35°, and 45°, from which Pareto-optimal solutions were identified based on classical non-dominance criteria. Pairwise 2D projections of the Pareto front enabled visualization of trade-offs and revealed γ = 35° as the Pareto knee-point, representing the most balanced compromise among high deformation intensity, increased uniformity, and reduced energy consumption. This optimal angle was further corroborated through a normalized weighted sum of the objective functions. The findings provide a validated reference for designing prototype deforming tools and support future experimental validation.

This work presents a comprehensive study on the fabrication, microstructural evolution, and mechanical performance of hybrid aluminum matrix composites based on Al6060 alloy reinforced with ~2 wt.% TiB₂ and ~1 wt.% multi-walled carbon nanotubes (MWCNTs). The composites were produced via ultrasonically assisted stir casting followed by radial-shear rolling (RSR). The combined processing route enabled a uniform distribution of reinforcing phases and significant grain refinement in the aluminum matrix. SEM, EDS, XRD, and EBSD analyses revealed that TiB₂ particles acted as nucleation centers and grain boundary pinning agents, while MWCNTs provided a network structure that suppressed agglomeration of ceramic particles and enhanced interfacial load transfer. As a result, hybrid composites demonstrated a submicron-grained structure with reduced anisotropy. Mechanical testing confirmed that yield strength (YS) and ultimate tensile strength (UTS) increased by 67% and 38%, respectively, in the cast state compared to unreinforced Al6060, while after RSR processing, YS exceeded 115 MPa and UTS reached 164 MPa, with elongation preserved at 14%. Microhardness increased from 50.2 HV0.2 (base alloy) to 82.2 HV0.2 (hybrid composite after RSR). The combination of ultrasonic melt treatment and RSR thus provided a synergistic effect, enabling simultaneous strengthening and ductility retention. These findings highlight the potential of hybrid Al6060/TiB₂–MWCNT composites for structural applications requiring a balance of strength, ductility, and wear resistance.

We report a scalable route to hybrid aluminum matrix composites (AMCs) based on Al6060 (as-fabricated condition) reinforced with 2 wt.% TiB₂ and 1 wt.% microsilica, fabricated by ultrasonically assisted stir casting (UASC) followed by radial-shear rolling (RSR). Premixing and preheating of powders combined with acoustic cavitation/streaming during UASC ensured uniform, non-sedimentary particle dispersion and low-defect cast billets. X-ray diffraction of the as-cast composite shows fcc-Al with weak TiB₂ reflections and no reaction products; microsilica remains amorphous. Electron microscopy and EBSD after RSR reveal full erasure of cast dendrites, fine equiaxed grains, weakened texture, and a high fraction of high-angle boundaries due to the concurrent action of particle-stimulated nucleation (micron-scale TiB₂) and Zener pinning/Orowan strengthening (50–350 nm microsilica). Mechanical testing shows that, in the cast state—comparing cast monolithic Al6060 to the cast hybrid-reinforced composite—yield strength (YS) increases from 61.7 to 77.2 MPa and ultimate tensile strength (UTS) from 103.4 to 130.7 MPa, without loss of ductility. After RSR to Ø16 mm (cumulated true strain ≈ 0.893), the hybrid attains YS 101.2 MPa, UTS 150.6 MPa, and elongation ≈ 22.0%, i.e., comparable strength to rolled Al6060 (UTS 145.1 MPa) while restoring/raising ductility by ~9.7 percentage points. Microhardness follows the same trend, increasing from 50.2 HV0.2 to 73.1 HV0.2 when comparing the base cast condition with the rolled hybrid. The route from UASC to RSR thus achieves a favorable mechanical strength–ductility balance using an economical, eco-friendly oxide/boride hybrid reinforcement, making it attractive for formable AMC bar and rod products.

One of the relevant goals in forging technologies is simplifying the existing process and developing new processes that can retain the original or very close to the original dimensions and billet shape after the end of the deformation cycle. This study attempts to develop a forging equipment design that provides alternating cyclic loading; the alternate cyclic forging (ACF) method is proposed. To preliminary evaluate the ACF and study the plastic deformation behavior, numerical simulation via finite element modeling (FEM) was conducted using DEFORM-3D. The main attention was paid to the metal flow characteristics, effective strain and stress distribution, and the forging load. The ACF results in non-uniform metal flow with the formation of diagonal and vortex flows were demonstrated. Maximum effective strains and stresses zones are localized at two points of the billet contact with the surface of the tooling container and at two points of the interface between the punches. It was also assumed that reducing the contact area between the punch and the billet using separate semi-cylindrical punches can reduce the forging load. Preliminary finite element analysis (FEA) results of the proposed process after four successive steps of the deformation cycle confirmed the feasibility of its general implementation.