Wannarat Chueangchayaphan

Dr. Wannarat Chueangchayaphan

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 February 2023 in Industrial Crops and Products
Verified
Journal Article
Closed access
PNPhatchariya Nooun
Phatchariya Nooun
NCNarong Chueangchayaphan
Narong Chueangchayaphan
NUNittaya Ummarat
Nittaya Ummarat
WCWannarat Chueangchayaphan
Wannarat Chueangchayaphan

21 June 2017 in Journal of Polymer Research
Verified
Journal Article
Closed access
PDF file
WCWannarat Chueangchayaphan
Wannarat Chueangchayaphan
VTVaraporn Tanrattanakul
Varaporn Tanrattanakul
NCNarong Chueangchayaphan
Narong Chueangchayaphan
SMSuchanya Muangsap
Suchanya Muangsap
WBWarisara Borapak
Warisara Borapak

2 December 2022 in Polymers
Verified
Journal Article
Open access
PDF file
WCWannarat Chueangchayaphan
Wannarat Chueangchayaphan
PLPiyawadee Luangchuang
Piyawadee Luangchuang
NCNarong Chueangchayaphan
Narong Chueangchayaphan
Recently, dielectric elastomer actuators (DEA) have emerged as one of the most promising materials for use in soft robots. However, DEA needs a high operating voltage and high mechanical properties. By increasing the dielectric constant of elastomeric materials, it is possible to decrease the operating voltage required. Thus, elastomeric composites with a high dielectric constant and strong mechanical properties are of interest. The aim of this research was to investigate the effect of titanium dioxide (TiO2) content ranging from 0 to 110 phr on the cure characteristics, and physical, dielectric, dynamic mechanical, and morphological properties of acrylonitrile butadiene rubber (NBR) composites. The addition of TiO2 reduced the scorch time (ts1) as well as the optimum cure time (tc90) but increased the cure rate index (CRI), minimum torque (ML), maximum torque (MH), and delta torque (MH − ML). The optimal TiO2 content for maximum tensile strength and elongation at break was 90 phr. Tensile strength and elongation at break were increased by 144.8% and 40.1%, respectively, over pure NBR. A significant mechanical property improvement was observed for TiO2-filled composites due to the good dispersion of TiO2 in the NBR matrix, which was confirmed by scanning electron microscopy (SEM). Moreover, incorporating TiO2 filler gave a higher storage modulus, a shift in glass transition temperature (Tg) to a higher temperature, and reduced damping in dynamic mechanical thermal analysis (DMTA). The addition of TiO2 to NBR rubber increased the dielectric constant of the resultant composites in the tested frequency range from 102 to 105 Hz. As a result, TiO2-filled NBR composite has a high potential for dielectric elastomer actuator applications.

15 April 2018 in Polymer International
Verified
Journal Article
Closed access
PDF file
WCWannarat Chueangchayaphan
Wannarat Chueangchayaphan
NCNarong Chueangchayaphan
Narong Chueangchayaphan
VTVaraporn Tanrattanakul
Varaporn Tanrattanakul
SMSuchanya Muangsap
Suchanya Muangsap

21 November 2019 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
PDF file
WBWarisara Borapak
Warisara Borapak
NCNarong Chueangchayaphan
Narong Chueangchayaphan
SPSkulrat Pichaiyut
Skulrat Pichaiyut
WCWannarat Chueangchayaphan
Wannarat Chueangchayaphan

31 August 2020 in Polymer International
Verified
Journal Article
Closed access
PDF file
PLPiyawadee Luangchuang
Piyawadee Luangchuang
NCNarong Chueangchayaphan
Narong Chueangchayaphan
MSMuhammad Azwadi Sulaiman
Muhammad Azwadi Sulaiman
WCWannarat Chueangchayaphan
Wannarat Chueangchayaphan