Csaba Felhő

Dr. Csaba Felhő

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2015 in Procedia CIRP
Verified
Journal Article
Open access
CFCsaba Felhő
Csaba Felhő
BKBernhard Karpuschewski
Bernhard Karpuschewski
JKJános Kundrák
János Kundrák
The ability to plan the quality of surfaces is very important in manufacturing due to the fulfillment of requirements for parts machined by different methods. A method and a modelling procedure are introduced in the paper based on the definition of the relations between the calculated theoretical and the measured real roughness values of machined surfaces. Cutting experiments were performed for the determination of the real roughness data where the evolution of surface roughness was investigated with varied technological parameters. Finally, the calculated relations between the theoretical and real values are presented,allowing the prediction of the expected roughness of surfaces machined with the given conditions

5 March 2022 in Machines
Verified
Journal Article
Open access
PDF file
CFCsaba Felhő
Csaba Felhő
GVGyula Varga
Gyula Varga
Surface roughness is an important factor in metal cutting, and usually different surface roughness characteristics are used to control the quality of the machined surfaces. However, as the cutting tool wears out during the cutting process, the roughness values change. In most cases, theoretical roughness values are calculated without taking the wear characteristics of the tool into account. For this reason, the calculated and measured roughness values may differ from each other, and the tendency of their change may also be different. This paper presents a method for the determination of the theoretical roughness of hard turned surfaces considering the wear of the cutting tool. The purpose of the analyses performed was to show the effect of wear trace on the tool and the roughness of the machined surface and to give a possible method to take the wear into account when calculating the theoretical roughness values. During the investigations, the shape of the actual (worn) edge section of the cutting tool was recorded by an optical microscope, and the theoretical surface roughness values were calculated with that profile by a CAD modeling method developed earlier. Cutting experiments were conducted on a lathe machine with two similar cutting tools, one of them has significant tool wear, while the other was a completely new one. The calculated theoretical roughness values were compared with real measured roughness values, and the error of the estimates was between 8.7 and 68.3%, larger errors were found at lower feeds.

1 January 2021 in CIRP Journal of Manufacturing Science and Technology
Verified
Journal Article
Open access
JKJános Kundrák
János Kundrák
BKBernhard Karpuschewski
Bernhard Karpuschewski
ZPZoltán Pálmai
Zoltán Pálmai
CFCsaba Felhő
Csaba Felhő
TMTamás Makkai
Tamás Makkai
DBDmytro Borysenko
Dmytro Borysenko

1 December 2011 in Key Engineering Materials
Verified
Journal Article
Closed access
PDF file
CFCsaba Felhő
Csaba Felhő
JKJános Kundrák
János Kundrák
The microgeometry of cut surfaces is one important characteristic of surface quality, since it has significant influence on the tribological properties of working surfaces. In addition to the ability to plan the economical effectiveness of cutting and the accuracy of workpieces the ability to plan the quality of machined surfaces has also emphasized importance. This is why the predictability of surface roughness in planning of technological processes is more and more important. More and more opportunities presenting themselves and one of these is the estimation of the expected value of roughness of the machined surface on the basis of the theoretical value of roughness. The paper focuses on the introduction of a method to describe a mathematical relation between the theoretical and the measured roughness indexes in cutting with tools having defined edge geometry, thus the planning may be more accurate.

1 June 2016 in Manufacturing Technology
Verified
Journal Article
Open access
PDF file
JKJanos Kundrak
Janos Kundrak
CFCsaba Felhő
Csaba Felhő
At design of cutting tools the positioning of cutting edges and geometry of cutting inserts are becoming increasingly diversified with the development of cutting procedures. As a result, the generated tool marks on cut surfaces also can take m...

1 January 2019 in CIRP Journal of Manufacturing Science and Technology
Verified
Journal Article
Closed access
DBDmytro Borysenko
Dmytro Borysenko
BKBernhard Karpuschewski
Bernhard Karpuschewski
FWFlorian Welzel
Florian Welzel
JKJános Kundrák
János Kundrák
CFCsaba Felhő
Csaba Felhő