Polymeric composites (PC) of tribological applications with a high level of physical, mechanical and thermal properties based on aromatic polyamide and silica gel have been developed. Regularities have been obtained that describe the effect of the filler content in PC on the friction coefficient, temperature on the friction surface and the intensity of linear wear rate of the studied PC-steel friction pair. It was found that the optimal silica gel content in the polymer matrix is 10 wt %. The morphology of the steel surface of friction after friction interaction with PC based on aromatic polyamide and silica gel was studied. The formation of an antifriction film on the steel surface of friction was discovered, which contributes to a decrease in the friction coefficient, temperature on the friction surface, and the linear wear intensity of the studied PC. The influence of the load and sliding speed on the main tribotechnical characteristics of the PC-steel friction pair has been studied. Mathematical laws were derived that describe the influence of the main external factors (load and sliding speed) on the friction coefficient and intensity of linear wear rate of the studied friction pair. Physical, mechanical and thermal investigations of the developed PC were carried out and it was found that the introduction of 10 wt % silica gel contributes to their 5–10 % increase.
This paper reports a laboratory study of the physical, mechanical, and thermal properties of designed composite materials based on Phenylone C1 filled with silica gel. Structural plastics, due to their high chemical and wear resistance, sufficient level of physical, mechanical, and thermal properties, can significantly improve the technical characteristics of machines and mechanisms. However, some structural plastics, including Phenylone C1, have a significant drawback – a narrow temperature range of their processing, which leads to a complication of technological equipment and increases the cost of production. It was established that the technical processing of the initial composite material into finished products could be improved by introducing fillers. The regularities of influence of silica gel content on the level of thermal and physical-mechanical properties of polymer composite materials based on Phenylone C1 have been established. It was found that the introduction of silica gel into Phenylone C1 leads to an increase in stress at the yield strength and modulus of elasticity at compression by 6.3 % and 13.3 %, respectively, compared to the original material. It was established that the heat resistance of the filled composite increases by 11.6 % with a decrease in thermal linear expansion by 10‒20 %, depending on the content of the filler. It was found that with an increase in silica gel concentration in the polymer matrix, the temperature of the onset of active destruction shifts towards higher temperatures. When filled in the amount of 30 % by weight, this temperature reaches 375 °C, which increases the temperature range of processing the designed material by 25 °C. The study results make it possible to optimize the system of tolerances and landings of parts made of polymer-composite materials, simplify the technology of their manufacture, and, as a result, reduce their cost
Вступ. Розвиток авіаційної та космічної промисловості сприяє не тільки створенню сучасних літаків, ракет та космічних апаратів, а й позитивно впливає на суміжні галузі промисловості.Проблематика. Однією із основних вимог до продукції авіаційної та космічної промисловості є високий рівень її надійності та довговічності, що обумовлено постійною взаємодією із людьми та досить високою собівартістю виготовлення й експлуатації. Найбільш актуальним це є для сучасних літаків, ракет та космічних апаратів, які експлуатуються при більших швидкостях, температурах, навантаженнях тощо, ніж попередники. Тому підвищення надійності й довговічності у роботі продукції авіаційної та космічної промисловості є актуальним напрямком.Мета. Підвищити надійність та довговічність основних вузлів ракето-космічної техніки за рахунок заміни матеріалів, з яких вони виготовлені, на власні інноваційні розробки.Матеріали й методи. Об’єктами досліджень були полімерні композиційні матеріали на основі фторполімерів та ароматичних поліамідів, які наповнені дисперсними матеріалами на основі діоксиду кремнію та вуглецю.Результати. Розроблено склад та технології переробки у вироби полімерних композиційних матеріалів на основі фторполімерів та ароматичних поліамідів. Встановлено, що за рівнем міцності (до 285 МПа) вони перевищують більшість кольорових металів, їніх сплавів і низьковуглецевих сталей, маючи при цьому низьку густину (до 1400 кг/м3). За теплофізичними властивостями вони належать до найбільш термостійких матеріалів на основі полімерів (не підлягають термічному розкладанню до температур +365 oС). Показано, що деталі із розроблених матеріалів можуть працювати у вузлах тертя без змащування у нормальному режимі роботи при навантаженнях до 2,5 МПа.Висновки. Розроблено полімерні композиційні матеріали на основі фторполімерів та ароматичних поліамідів з високим рівнем властивостей, деталі з яких значно покращують рівень надійності та довговічності сучасних літаків, ракет і космічних апаратів.
25 May 2023 in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Without the employment of new equipment, with units functioning at high levels of weights, sliding speeds and temperatures, the current growth of the sector is all but impossible. High levels of labour intensity have a detrimental impact on the dependability and durability of the product. Moving joints, which comprise friction units, frequently fail at the same time. It is vital to increase their dependability and durability. This can be accomplished by substituting more recent materials with higher-quality qualities for the friction pair materials. To create such materials, the researchers created an aromatic polyamide polymer that was filled with silicon- (silica gel, bentonite) and carbon-containing (technical carbon, graphite) components. It was determined that depending on their nature, structure and content in the polymer matrix, the addition of these fillers enables the reduction of the coefficient of friction and wear of the produced polymer composites by 1.5–2.5 and 20–40 times, respectively, during frictional interaction with steel. It was found that 10–15% by weight of the examined fillers in aromatic polyamide is the ideal concentration. It has been proven that polymer composites filled with layered materials (bentonite, graphite) perform better in terms of tribological qualities when in contact with steel than those filled with spherical elements (technical carbon, silica gel). The improvement of the tribological properties of the developed polymer composites in comparison to the original polymer was determined based on the microphotographs of steel surfaces and the study of their morphological (roughness) and physical (microhardness) properties. It was determined that the change in the friction nature was due to the creation of an antifriction coating on the metal friction surface from the products of tribochemical reactions occurring during friction.