The purpose of this work is to define optimal growth conditions to maximise biomass for batch culture of the cyanobacterium Arthrospira maxima and the microalgae Chlorella vulgaris, Isochrysis galbana and Nannochloropsis gaditana. Thus, we study the effect of three variables on cell growth: i.e., inoculum:culture medium volume ratio (5:45, 10:40, 15:35 and 20:30 mL:mL), light:dark photoperiod (8:16, 12:12 and 16:8 h) and type of culture medium, including both synthetic media (Guillard’s F/2 and Walne’s) and wastewaters. The results showed that the initial inoculum:culture medium volume ratio, within the range 5:45 to 20:30, did not affect the amount of biomass at the end of the growth (14 days), whereas high (18 h) or low (6 h) number of hours of daily light was important for cell growth. The contribution of nutrients from different culture media could increase the growth rate of the different species. A. maxima was favoured in seawater enriched with Guillard’s F/2 as well as C. vulgaris and N. gaditana, but in freshwater medium. I. galbana had the greatest growth in the marine environment enriched with Walne’s media. Nitrogen was the limiting nutrient for growth at the end of the exponential phase of growth for C. vulgaris and N. gaditana, while iron was for A. maxima and I. galbana. The growth in different synthetic culture media also determines the biochemical composition of each of the microalgae. All species demonstrated their capability to grow in effluents from a wastewater treatment plant and they efficiently consume nitrogen, especially the three microalga species.

The production of fatty acids ethyl esters (FAEEs) to be used as biodiesel from oleaginous microalgae shows great opportunities as an attractive source for the production of renewable fuels without competing with human food. To ensure the economic viability and environmental sustainability of the microbial biomass as a raw material, the integration of its production and transformation into the biorefinery concept is required. In the present work, lipids from wet Isochrysis galbana microalga were extracted with ethyl acetate with and without drying the microalgal biomass (dry and wet extraction method, respectively). Then, FAEEs were produced by lipase-catalyzed transesterification and esterification of the extracted lipids with ethanol using lipase B from Candida antarctica (CALB) and Pseudomonas cepacia (PC) lipase supported on SBA-15 mesoporous silica functionalized with amino groups. The conversion to FAEEs with CALB (97 and 85.5 mol% for dry and wet extraction, respectively) and PC (91 and 87 mol%) biocatalysts reached higher values than those obtained with commercial Novozym 435 (75 and 69.5 mol%). Due to the heterogeneous nature of the composition of microalgae lipids, mixtures with different CALB:PC biocatalyst ratio were used to improve conversion of wet-extracted lipids. The results showed that a 25:75 combi-lipase produced a significantly higher conversion to FAEEs (97.2 mol%) than those produced by each biocatalyst independently from wet-extracted lipids and similar ones than those obtained by each lipase from the dry extraction method. Therefore, that optimized combi-lipase biocatalyst, along with achieving the highest conversion to FAEEs, would allow improving viability of a biorefinery since biodiesel production could be performed without the energy-intensive step of biomass drying.

The yield and composition of the biocrude obtained by hydrothermal liquefaction (HTL) of Nannocloropsis gaditana using heterogeneous catalysts were evaluated. The catalysts were based on metal oxides (CaO, CeO₂, La₂O₃, MnO₂, and Al₂O₃). The reactions were performed in a batch autoclave reactor at 320 °C for 10 min with a 1:10 (wt/wt) microalga:water ratio. These catalysts increased the yield of the liquefaction phase (from 94.14 ± 0.30 wt% for La₂O₃ to 99.49 ± 0.11 wt% for MnO₂) as compared with the thermal reaction (92.60 ± 1.20 wt%). Consequently, the biocrude yields also raised in the metal oxides catalysed HTL, showing values remarkably higher for the CaO (49.73 ± 0.9 wt%) in comparison to the HTL without catalyst (42.60 ± 0.70 wt%). The N and O content of the biocrude obtained from non-catalytic HTL were 6.11 ± 0.02 wt% and 10.50 ± 0.50 wt%, respectively. In this sense, the use of the metal oxides decreased the N content of the biocrude (4.62 ± 0.15–5.45 ± 0.11 wt%), although, they kept constant or increased its O content (11.39 ± 2.06–21.68 ± 0.03 wt%). This study shows that CaO, CeO₂ and Al₂O₃ can be promising catalysts based on the remarkable amount of biocrude, the highest values of C, H, heating value, energy recovery, and the lowest content of N, O and S.

Research into the extraction of phycobiliprotein from Arthrospira platensis is currently ongoing. Most traditional methods of phycobiliprotein extraction include the use of organic solvents, which negatively affect the sustainability of the process. Ionic liquids (ILs) are a promising alternative for phycobiliprotein extraction due to their properties as green solvents. In the present work an imidazolium‐based IL and sonication were studied for phycobiliprotein and carbohydrate extraction. A factorial experimental design was used to optimize the amount of extracted phycocyanin. The maximum extraction yield was achieved by using low biomass/solvent ratios combined with high IL/water ratios and sonication powers, and long operation times. The recovery of IL was studied under these conditions using a dialysis‐based process to separate the IL from the extracted phycobiliproteins. The results reveal the possibility of using the recovered IL for seven consecutive extraction cycles with an acceptable phycocyanin extraction amount, from 75 mg g⁻¹ (fresh IL) to 60 mg g⁻¹ (7 cycles of reused IL). The use of [Emim] [EtSO₄] + ultrasound is a promising alternative for phycocyanin extraction, enhancing the results obtained with other IL in terms of extracted phycocyanin and the number of times the IL can be reused. © 2021 Society of Chemical Industry and John Wiley & Sons, Ltd