Electrosprayed polycaprolactone (PCL) microparticles are widely used in medical tissue engineering, drug control release delivery, and food packaging due to their prominent structures and properties. In electrospraying, the selection of a suitable solvent system as the carrier of PCL is fundamental and a prerequisite for the stabilization of electrospraying, and the control of morphology and structure of electrosprayed particles. The latter is not only critical for diversifying the characteristics of electrosprayed particles and achieving improvement in their properties, but also promotes the efficiency of the process and deepens the applications of electrosprayed particles in various fields. In order to make it systematic and more accessible, this review mainly concludes the effects of different solution properties on the operating parameters in electrospraying on the formation of Taylor cone and the final structure as well as the morphology. Meanwhile, correlations between operating parameters and electrospraying stages are summarized as well. Finally, this review provides detailed guidance on the selection of a suitable solvent system regarding the desired morphology, structure, and applications of PCL particles.
Electrosprayed poly(caprolactone) (PCL) microparticles were produced using five solvents (ethyl acetate, acetone, anisole, glacial acetic acid and chloroform) under different PCL concentrations and operating parameters. Not only green and appropriate solvent for PCL electrospraying was pointed out, but also the effects of solution properties (surface tension, electrical conductivity, viscosity and vapor pressure) and operating parameters (flow rate, working distance and applied voltage) on the formation of electrosprayed particles were clarified. The formation and shape of Taylor cone during electrospraying was observed by high-speed images captured with a camera, and the size and morphology of electrosprayed particles were characterized by optical and scanning electron microscopies. It can conclude that the cone–jet range of applied voltage mainly depended on electrical conductivity, and an ideal Taylor cone was easier to form under high viscosity and low surface tension. Although high electrical conductivity was a contributor to fabricate tiny particles, it was easier to fabricate mono-dispersed microparticles under low electrical conductivity. The poly-dispersed distribution obtained with a high electrical conductivity converted into mono-dispersed distribution with the increasing of viscosity. Furthermore, the size of electrosprayed particles also correlated with the surface tension and vapor pressure of the solvent used. Ethyl acetate, due to mild electrical conductivity and surface tension, moderate viscosity and vapor pressure, is a green and suitable solvent for PCL electrospraying. Single pore PCL microparticles with smooth cherry-like morphology can be prepared from ethyl acetate. Finally, long working distance not only stabilizes the break-up of charged jet, but also promotes the evaporation of solvent.
1 December 2017 in Advances in Engineering Software
A novel intumescent flame retardant (IFR) agent designated as Dohor-6000A has been used to prepare halogen-free flame retardant polypropylene (PP) fibers via melting spinning. Before being blended with PP resin, a surface modification of Dohor-6000A was carried out to improve its compatibility with the PP matrix. The rheological behavior of flame retardant Dohor-6000A/PP resin, the structure, morphology, mechanical properties, flammability of the Dohor-6000A/PP fibers were studied in detail, as well as the action mode of flame retardant. X-ray diffraction (XRD) showed that the addition of Dohor-6000A did not damage the crystal as well as the orientation structure of PP matrix, which was helpful to the maintenance of mechanical properties. The presence of the IFR significantly improved the flame retardant performance and thermal stability of PP fibers. When the content of Dohor-6000A reached 25%, the fibers displayed a limiting oxygen index (LOI) value of 29.1% and good melt-drop resistance. Moreover, the peak heat release rate (PHRR) and total heat release (THR) from microscale combustion colorimetry (MCC) tests were decreased by 26.0% and 16.0% in comparison with the same conditions for pure PP fibers. In the condensed phase, the IFR promoted a carbonization process and promoted the formation of a glassy or stable foam protective layer on the surface of the polymer matrix. In addition, the IFR decomposed endothermically to release of non-combustible gases such as NH3 and CO2 which dilutes the combustible gases in the combustion zone.
30 August 2023 in Industrial & Engineering Chemistry Research
Herein, inorganic silicon dioxide (SiO2) nanoparticles are deposited on the surface of continuous basalt fibers (CBFs) to enhance the interfacial interactions between CBFs and epoxy matrix (EP) and the tensile strength of composites. According to results from scanning electron microscopy and atomic force microscopy, the surface morphology of CBFs changes from smooth to rough with the increase of SiO2 deposition content. The rough surface plays a role of chock to make CBFs implant into the EP better, offering strong mechanical engagement effect to the interface between CBFs and EP. Therefore, the interfacial shear strength (IFSS) between CBFs and EP and the tensile strength of composites both increase. However, depositing excessive SiO2 nanoparticles also brings some porous structures on CBFs surface, becoming defects and stress concentration points to weaken the IFSS and the tensile strength of composites. Finally, a comparison between grafting organic aliphatic chains and depositing inorganic rigid nanoparticles about their effects on the surface roughness of modified CBFs and the interfacial interactions between modified fibers and matrix is carried out to clarify the reinforcing mechanisms of interfacial adhesion and the tensile strength of composites.