Grouting of fractured rock mass prior to excavation results in grout-filled discontinuities that govern the deformation characteristics of a site. The influence of joint characteristics on the properties of grouted rocks is important in assessing the effects of grouting on jointed rock mass. However, grouting remains a predominantly empirical practice and the effects of grouting on rock joint behavior and material properties have yet to be accurately assessed. Granular materials, including jointed rocks, typically display nonlinear strain-dependent responses that can be characterized by the shear modulus degradation curve. In this study, the effects of grouting on the strain-dependent shear stiffness of jointed rock mass were investigated at the small-strain (below 10⁻⁵) and mid-strain (10⁻⁵ to 10⁻³) ranges using the quasi-static resonant column test and rock mass dynamic test devices. The effects of curing time, axial stress, initial joint roughness, and grouted joint thickness were examined. The results show that (1) grouting of rock joints leads to decreased stress sensitivity and increased small-strain shear stiffness for all tested samples; (2) the grouted rock samples display similar modulus degradation characteristics as the applied grout material; (3) the initial joint roughness determines the stress-dependent behaviors and general stiffness range of the jointed and grouted rocks, but the strain-dependent behaviors are dependent on the properties of the grout material; (4) increased grouted joint thickness results in larger contribution of the grout properties in the overall grouted rock mass.

The presence of gouge in rock joints significantly affects the physical and mechanical properties of the host rock mass. Wave-based exploration techniques have been widely used to investigate the effects of gouge fill on rock mass properties. Previous research on wave propagation in gouge-filled joints focused on analytical and theoretical methods. The lack of experimental methods for multiple rock joint systems, however, has limited the verification potential of the proposed models. In this study, the effects of gouge material and thickness on wave propagation in equivalent continuum jointed rocks are investigated using a quasi-static resonant column test. Gouge-filled rock specimens are simulated using stacked granite rock discs. Sand and clay gouge fills of 2 and 5 mm thicknesses are tested to investigate the effects of gouge material and thickness. Comprehensive analyses of the effects of gouge thickness are conducted using homogeneous isotropic acetal gouge fills of known thickness. The results show that gouge fill leads to changes in wave velocity, which depend on the characteristics of the gouge fill. The results also show that particulate soil gouge is susceptible to preloading effects that cause permanent changes in the soil fabric and contact geometry and that increased gouge thickness causes a more significant stiffness contribution of the gouge material properties to the overall stiffness of the equivalent continuum specimen. The normal and shear joint stiffnesses for different gouge fill conditions are calculated from the experimental results using the equivalent continuum model and suggested as input parameters for numerical analysis.

The estimation of hydraulic and mechanical properties of bedrock is important for the evaluation of energy-related structures, including high-level nuclear waste repositories, hydraulic fracturing wells, and gas-hydrate production wells. The hydraulic conductivity and stress–strain curves of rocks are conventionally measured through laboratory tests on cylindrical samples. Both ASTM standards for hydraulic conductivity and compressive strength involve the use of the planar bases of a cylindrical sample. Hence, an alternative test method is required for the simultaneous measurement of hydraulic conductivity and stress–strain curves. This study proposes a novel electrical resistivity estimation method using two perimeter electrodes for the estimation of hydraulic properties. The theoretical background for the perimeter electrode setup is derived and the COMSOL MultiPhysics^® finite element numerical simulation tool is employed to verify the derived theoretical equation. The accuracy of the numerical simulation tool is first validated by simulating the ASTM standard testing method for electrical resistivity. The electrical resistance values derived from the theoretical equation and numerical simulation are compared for different electrical resistivity and electrode radius. The assumed equidistant, circular equipotential surface results in a theoretical lower bound for the measured electrical resistance in the cylindrical specimen. The introduction of a phenomenological distortion factor to correct for the theoretical equipotential surface results in a good fit with the numerical simulation results. The effects of electrode length and equivalent strap electrodes were investigated to assess the applicability of the suggested method for laboratory testing. Consequently, this study presents an effective alternative theoretical assessment method for the lower bound electrical resistivity of cylindrical rock core samples under confining conditions when the installation of base electrodes is infeasible.

Korea has officially initiated the development of an underground research laboratory (URL) at a depth of 500 m to facilitate a full-scale demonstration of high-level radioactive waste disposal technology. With the establishment of the URL, validating the long-term performance of the engineered barrier system (EBS) under deep geological conditions has become a critical priority. This paper presents Korea’s research plans and technological advancements in the long-term safety evaluations of EBS, a key component of a recently launched multi-ministerial R&D project for spent nuclear fuel management. The primary objective of this project is to assess the long-term integrity of EBS by analyzing coupled interactions with the disposal system as the real disposal environment evolves. The research is divided into four key areas: (1) establishing performance criteria for engineered barrier materials, (2) characterizing interactions among EBS components, (3) investigating coupled Thermo-Hydro-Mechanical-Chemical (THMC) behaviors, and (4) developing core technologies for in situ validation of EBS performance and coupled interactions. This nine-year project (2021–2029) is currently in its second phase(2024–2026), focusing on engineering-scale experiments, numerical model development, and preparation for large-scale field demonstration in the third phase. The outcomes of this study are expected to enhance the scientific basis for safety assessments and licensing in a disposal repository, as well as serve as a bridge for full-scale research at actual disposal depths utilizing URLs.