This study investigates the influence of varying layer thickness through interlayer machining in Wire Arc Additive Manufacturing (WAAM) and its impact on microstructural evolution, mechanical properties, and residual stress distribution. It compares four types of WAAM samples: As-built with uneven layer thickness without interlayer machining and uniform layer thicknesses of 2 mm, 1.5 mm, and 1 mm achieved through interlayer machining. As-built components exhibited coarse columnar grains and uneven deposition, adversely affecting hardness and strength. Interlayer machining at reduced layer thickness refined grains, restricted growth, and induced plastic deformation, leading to enhanced mechanical properties. Grain refinement achieved reductions of 62.7% (top), 77.6% (middle), and 64.3% (bottom), significantly improving microstructural uniformity. Microhardness increased from 150 to 180 HV (as-built) to 210 to 230 HV (machined to maintain 1 mm layer thickness), marking a 40–43% improvement. Tensile strength was enhanced, with UTS increasing from 494.72 MPa to 582.11 MPa (17.6%) and YS from 371 MPa to 471 MPa (26.9%), although elongation decreased from 59% to 46% (22% reduction). Residual stress was reduced by 55–60%, improving structural integrity. These findings highlight interlayer machining as a key strategy for optimizing WAAM-fabricated components while balancing mechanical performance and manufacturing efficiency.
Additive manufacturing (AM) has evolved to enable the direct production of functional components through the hybridization of additive and subtractive processes. In metal wire AM, hybridization is key, encompassing process integration (addition/subtraction), energy source combinations (arc/laser), kinematic options (3/4/5 axis), and slicing techniques (planar/conformal). This paper focuses on these hybridization methods, with a unified system designed for single-machine setups, improving efficiency and accuracy. This study presents a detailed exploration of these hybridization levels through the fabrication of a complex 5-axis geometry—an impeller. The impeller was manufactured with hybridization using various levels and subsequently compared with manufacturing processes like additive manufacturing with interlayer machining and traditional machining methods. The hybrid approach significantly reduced the manufacturing time for the selected impeller geometry from 3536 min to 792 min (saving 77.6% manufacturing time) and minimized material waste to 9.3%, compared with 74.07% in traditional machining. This demonstrates a more efficient, precise, and cost-effective method to optimize metal wire AM for producing complex metal components, advancing capabilities and applications.
Rapid prototyping has advanced into additive manufacturing (AM), enabling direct production of functional components through a hybrid approach combining additive and subtractive processes. In metal-wire AM, arc and laser energy sources are common, with geometry complexity influencing kinematic choices (3/4/5 axis) and necessitating tailored slicing techniques. Whereas this paper explores various levels of hybridization, essential for creating functional components using the metal-wire AM process. These levels encompass process hybridization (addition/subtraction), energy source hybridization (arc/laser), kinematics hybridization (3/4/5 axis), and slicing technique hybridization (planar/conformal). A unified system was designed to accommodate all levels of hybridization on a single machine with a single setup that minimizes the time and improves accuracy. The study presents a detailed exploration of these hybridization levels through the fabrication of a complex 5-axis geometry—an impeller. The impeller was manufactured with hybridization using various levels and subsequently compared with manufacturing processes like additive manufacturing with interlayer machining and traditional machining methods. The hybrid approach significantly reduced the manufacturing time for the selected impeller geometry from 3536 minutes to 792 minutes (saving 77.6% manufacturing time) and minimized material waste to 9.3%, compared to 74.07% in traditional machining. This demonstrates a more efficient, precise, and cost-effective method for producing complex metal components. Furthermore, it offers critical insights into the effectiveness of this hybrid method by optimizing metal-wire AM processes for intricate geometries, thereby advancing the capabilities and applications of metal-wire AM technology.
This study focuses on how varying layer thickness by interlayer machining affects microstructure refinement, mechanical properties, and residual stresses of Wire Arc Additive Manufacturing (WAAM) components. It compares four types of WAAM samples: As built with uneven layer thickness without interlayer machining and uniform layer thicknesses of 2mm, 1.5mm, and 1mm achieved through interlayer machining. It reveals that the machining force reduces grain size and residual stress in WAAM components. Moreover, uniform and smaller layer thickness enhances inter-layer bonding, improving mechanical properties but increases the build time with more layers of deposition.