Minyun Hu

Dr. Minyun Hu

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 September 2010 in Granular Matter
Verified
Journal Article
Open access
PDF file
MHMinyun Hu
Minyun Hu
COCatherine O’sullivan
Catherine O’sullivan
RJRichard R. Jardine
Richard R. Jardine
MJMingjing Jiang
Mingjing Jiang
The anisotropy of a granular material’s structure will influence its response to applied loads and deformations. Anisotropy can be either inherent (e.g. due to depositional process) or induced as a consequence of the applied stresses or strains. Discrete element simulations allow the interactions between individual particles to be explicitly simulated and the fabric can be quantified using a fabric tensor. The eigenvalues of this fabric tensor then give a measure of the anisotropy of the fabric. The coordination number is a particle scale scalar measure of the packing density of the material. The current study examines the evolution of the fabric of a granular material subject to cyclic loading, using two-dimensional discrete element method (DEM) simulations. Isotropic consolidation modifies and reduces the inherent anisotropy, but anisotropic consolidation can accentuate anisotropy. The ratio of the normal to shear spring stiffness at the particle contacts in the DEM model affects the evolution of anisotropy. Higher ratios reduce the degree of anisotropy induced by anisotropic consolidation. The anisotropy induced by cyclic loading depends on the amplitude of the loading cycles and the initial anisotropy.

22 May 2025 in Applied Ocean Research
Verified
Journal Article
Open access
MLMingzhu Li
Mingzhu Li
MSMiaojun Sun
Miaojun Sun
ZSZhigang Shan
Zhigang Shan
MHMinyun Hu
Minyun Hu
SWShuaifeng Wu
Shuaifeng Wu
MJMingjing Jiang
Mingjing Jiang

16 November 2021 in Geofluids
Verified
Journal Article
Open access
PDF file
XBXiao Bin
Xiao Bin
MHMinyun Hu
Minyun Hu
PZPeijiao Zhou
Peijiao Zhou
YLYuke Lu
Yuke Lu
YZYong Zhang
Yong Zhang
As one of the basic mechanical properties of soil, the creep property of a given type soil is related to stress path, and stress level. In this paper, triaxial shear creep tests under different deviatoric stress levels were performed on both intact sample and the reconstituted sample of clay taken from Hangzhou, China. Based on the Boltzmann linear superposition principle, the creep curves of the clay sample under different levels of deviatoric stress were obtained, and the creep characteristics of the intact sample and the reconstituted sample were compared in both total stress creep analysis and effective stress creep analysis. Furthermore, the creep curves were fitted using a hyperbolic creep model. The results show that (1) under the same stress level, the creep of intact sample evolves more than that of reconstituted sample; (2) the hyperbolic creep model is suited to describe the creep characteristics of intact and reconstituted clay, and the model parameters and can be linearly correlated to the stress level ; (3) for the application of the hyperbolic model, the total stress analysis works better, and the model parameters and can be determined by a linear relationship with Dr.

17 September 2021
Verified
Book Chapter
Closed access
PDF file
MHMinyun Hu
Minyun Hu
JYJing-Tian Yang
Jing-Tian Yang
LPLi-Dong Pan
Li-Dong Pan
KPKong-Shu Peng
Kong-Shu Peng
YLYu-Ke Lu
Yu-Ke Lu

3 August 2018
Verified
Book Chapter
Closed access
PDF file
MHMinyun Hu
Minyun Hu
BXBin Xiao
Bin Xiao
SWShuchong Wu
Shuchong Wu
PZPeijiao Zhou
Peijiao Zhou
YLYuke Lu
Yuke Lu

11 January 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
MWMingyuan Wang
Mingyuan Wang
MHMinyun Hu
Minyun Hu
CLChaohua Li
Chaohua Li
Xiaobing XuXiaobing Xu
Xiaobing Xu
ZYZefemg Ye
Zefemg Ye
QHQi Hu
Qi Hu
To investigate the excavation characteristics and mechanisms of a deep foundation under lateral confined water pressure, a model test was conducted with real-time monitoring of the stress and deformation of the foundation strut system. The results indicate that in stages 1 and 3 (the process of raising the lateral confined water level, O and F), the rise in lateral confined water levels caused the diaphragm wall to shift inward. However, the reduction in earth pressure due to the inward shift of the diaphragm wall exceeded the increase in water pressure from the raised confined water level, resulting in an overall decrease in lateral pressure on the diaphragm wall. During stage 2 (the excavation and supporting process, K1–Z4), as excavation and strut installation progressed, the lateral pressure on the diaphragm wall decreased, while both bending moment and horizontal displacement increased, with the most pronounced changes occurring when excavation reached the depth of the lateral confined aquifer. Upon reaching the soil layers within the depth of the lateral confined aquifer, the axial force of struts increased significantly, with the second level of strut experiencing the greatest axial force. In deep foundation design, it is essential to account for the maximum bending moment and horizontal displacement of the diaphragm wall within the depth range of the lateral confined aquifer, as well as the maximum vertical displacement in the range of 0.50%D–0.83%D outside the pit. Due to the rapid transmission of lateral confined water pressure changes in fine sand, and the delayed transmission in clay due to their low permeability, the diaphragm wall response is most pronounced within the depth range of the lateral confined aquifer.