A superhydrophobic and superoleophilic oil sorbent was prepared by attaching SiO₂ particles onto a cotton fiber surface by a sol–gel method and subsequent octadecyltrichlorosilane modification.

A new kind of hydrophobic and oil sorbent based on jute fiber was successfully prepared by the integration of silica onto a fiber surface via the sol-gel method and subsequent hydrophobic modification with octadecyltrichlorosilane (OTS). Compared with the hydrophilic raw fiber, the modified fiber had a water contact angle (CA) of 136.2°, suggesting that the material has good hydrophobicity. Furthermore, the ability of oil in the oil/water system (taking diesel for example) to absorb was revealed by the kinetics, the isotherm equation, and the thermodynamic parameters. Adsorption behavior was kinetically investigated using pseudo first-order and pseudo second-order models. The data mostly correlated with the pseudo first-order model. The equilibrium adsorption at 298 K was assessed by using the Langmuir and Freundlich isotherm models. The Freundlich model had greater consistency with the experimental data. The obtained thermodynamic parameters demonstrate that the adsorption of diesel is spontaneous, favorable, and exothermic.

The aim of this study was to isolate hydrocarbons-degrading bacteria for treatment of oily wastewater from long-standing petroleum-polluted sediments in Bohai Bay, China. Six hydrocarbons-degrading bacteria were screened and identified as Pseudomonas sp. and Bacillus sp. A new approach using a combination of various bacterial species in petroleum biodegradation was proposed and evaluated for its degradation characteristics. GC-FID analysis showed that mixed bacterial agents (YJ01) degraded 80.64% of crude oil and 76.30% of crude oil alkanes, exhibiting good biodegradation effect. Besides, after 14 days of culture, the biodegradation assessment markers, pristane and phytane, showed significant degradation rates of 46.75% and 78.23%, respectively. Kinetic analysis indicated that the degradation trends followed a single first-order kinetics model and the degradation half-life (t_1/2) of 15 g/L crude oil was significantly shorter (5.48 days). These results indicated that YJ01 could degrade a wider range of hydrocarbons as well as some recalcitrant hydrocarbon components, and can be applied for bioremediation and treatment of oil-contaminated environment.

To better understand the source and health risk of metal elements in PM_2.5, a field study was conducted from May to December 2018 in the central region of the Liaoning province, China, including the cities of Shenyang, Anshan, Fushun, Benxi, Yingkou, Liaoyang, and Tieling. 24 metal elements (Na, K, V, Cr, Mn, Co, Ni, Cu, Zn, As, Mo, Cd, Sn, Sb, Pb, Bi, Al, Sr, Mg, Ti, Ca, Fe, Ba, and Si) in PM_2.5 were measured by ICP-MS and ICP-OES. They presented obvious seasonal variations, with the highest levels in winter and lowest in summer for all seven cities. The sum of 24 elements were ranged from to in these cities. The element mass concentration ratio was the highest in Yingkou in the spring (26.15%), and the lowest in Tieling in winter (3.63%). The highest values of elements in PM_2.5 were mostly found in Anshan and Fushun among the studied cities. Positive matrix factorization (PMF) modelling revealed that coal combustion, industry, traffic emission, soil dust, biomass burning, and road dust were the main sources of measured elements in all cities except for Yingkou. In Yingkou, the primary sources were identified as coal combustion, metal smelting, traffic emission, soil dust, and sea salt. Health risk assessment suggested that Mn had non-carcinogenic risks for both adults and children. As for Cr, As, and Cd, there was carcinogenic risks for adults and children in most cities. This study provides a clearer understanding of the regional pollution status of industrial urban agglomeration.