Sumsun Naher

Dr. Sumsun Naher


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 February 2018 in Applied Physics A
Verified
Journal Article
Open access
PDF file
IKIsrat Rumana Kabir
Israt Rumana Kabir
DYDanqing Yin
Danqing Yin
NTN. Tamanna
N. Tamanna
SNSumsun Naher
Sumsun Naher
A two-dimensional thermomechanical finite element (FE) model of laser surface glazing (LSG) has been developed for H13 tool steel. The direct coupling technique of ANSYS 17.2 (APDL) has been utilised to solve the transient thermomechanical process. A H13 tool steel cylindrical cross-section has been modelled for laser power 200 W and 300 W at constant 0.2 mm beam width and 0.15 ms residence time. The model can predict temperature distribution, stress–strain increments in elastic and plastic region with time and space. The crack formation tendency also can be assumed by analysing the von Mises stress in the heat-concentrated zone. Isotropic and kinematic hardening models have been applied separately to predict the after-yield phenomena. At 200 W laser power, the peak surface temperature achieved is 1520 K which is below the melting point (1727 K) of H13 tool steel. For laser power 300 W, the peak surface temperature is 2523 K. Tensile residual stresses on surface have been found after cooling, which are in agreement with literature. Isotropic model shows higher residual stress that increases with laser power. Conversely, kinematic model gives lower residual stress which decreases with laser power. Therefore, both plasticity models could work in LSG for H13 tool steel.

25 January 2023 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Closed access
PDF file
MBM Nasir Bashir
M Nasir Bashir
AHA. S. M. A. Haseeb
A. S. M. A. Haseeb
SNSumsun Naher
Sumsun Naher
Muhammad Mahmood AliMuhammad Mahmood Ali
Muhammad Mahmood Ali
MBMohamed Bashir Ali Bashir
Mohamed Bashir Ali Bashir
IJIqra Javed
Iqra Javed

21 September 2022 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Closed access
PDF file
MBM Nasir Bashir
M Nasir Bashir
HSHafiz Muhammad Saad
Hafiz Muhammad Saad
MRMuhammad Rizwan
Muhammad Rizwan
SBSedat Bingöl
Sedat Bingöl
ICIftikhar Ahmed Channa
Iftikhar Ahmed Channa
SNSumsun Naher
Sumsun Naher

19 September 2022 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Closed access
PDF file
MBM Nasir Bashir
M Nasir Bashir
HSHafiz Muhammad Saad
Hafiz Muhammad Saad
MRMuhammad Rizwan
Muhammad Rizwan
MQM. M. Quazi
M. M. Quazi
Muhammad Mahmood AliMuhammad Mahmood Ali
Muhammad Mahmood Ali
SNSumsun Naher
Sumsun Naher

5 October 2019 in Metals
Verified
Journal Article
Open access
PDF file
BDBhagya Dasari
Bhagya Dasari
Dermot BrabazonDermot Brabazon
Dermot Brabazon
SNSumsun Naher
Sumsun Naher
Estimating the effect of graphene oxide (GO) reinforcement on overall properties of aluminum (Al) matrix composites experimentally is time-consuming and involves high manufacturing costs and sophisticated characterizations. An attempt was made in this paper to predict the mechanical properties of GO/Al composites by using a micromechanical finite element approach. The materials used for prediction included monolayer and multilayer GO layers distributed uniformly on the spherical Al matrix particles. The estimation was done by assuming that a representative volumetric element (RVE) represents the composite structure, and reinforcement and matrix were modeled as continuum. The load transfer between the GO reinforcement and Al was modeled using joint elements that connect the two materials. The numerical results from the finite element model were compared with Voigt model and experimental results from the GO/Al composites produced at optimized process parameters. A good agreement of numerical results with the theoretical models was noted. The load-bearing capacity of the Al matrix increased with the addition of GO layers, however, Young’s modulus of the GO/Al composites decreased with an increase in the number of layers from monolayer to 5 layers. The numerical results presented in this paper have demonstrated the applicability of the current approach for predicting the overall properties of composites.

23 September 2022 in Biological Trace Element Research
Verified
Journal Article
Closed access
PDF file
JBJameel Ahmed Baig
Jameel Ahmed Baig
ICIram Gul Chandio
Iram Gul Chandio
TKTasneem Gul Kazi
Tasneem Gul Kazi
HAHassan Afridi
Hassan Afridi
KAKhalil Akhtar
Khalil Akhtar
NMNiaz Ali Malghani
Niaz Ali Malghani