Małgorzata Sikora

Dr. Małgorzata Sikora

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2019 in Archives of Civil and Mechanical Engineering
Verified
Journal Article
Closed access
Lukasz StawinskiLukasz Stawinski
Lukasz Stawinski
Andrzej KosuckiAndrzej Kosucki
Andrzej Kosucki
Adrian MorawiecAdrian Morawiec
Adrian Morawiec
MSMałgorzata Sikora
Małgorzata Sikora

20 October 2017
Verified
Book Chapter
Closed access
PDF file
PLPaweł Lajmert
Paweł Lajmert
MSMałgorzata Sikora
Małgorzata Sikora
BKBogdan Kruszynski
Bogdan Kruszynski
DODariusz Ostrowski
Dariusz Ostrowski

2 January 2020 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
NKNorbert Kępczak
Norbert Kępczak
PZPiotr Zgórniak
Piotr Zgórniak
PLPaweł Lajmert
Paweł Lajmert
RRRadoslaw Rosik
Radoslaw Rosik
MSMałgorzata Sikora
Małgorzata Sikora
The paper examines the wear of end mill cutters, the parameters of a workpiece’s surface layer and the values of cutting forces during the machining of polymer concrete, which is one of the most difficult-to-cut materials. Increased abrasive wear of the active cutting edges is a result of the heterogeneous structure of this material, and it has a negative effect on the cutting process, the durability of the cutting tools as well as the roughness of the workpiece. It is very important to determine the machining parameters for this material from a tool durability and quality of machining point of view. The research was divided into two stages. In the first stage, the appropriate machining parameters were determined based on the measurement of the components of the cutting force. In the second stage, durability tests of four end mill cutters were carried out. During the tests, the component cutting forces, tool wear and surface roughness were measured. The highest tool durability was recorded for the monolithic cemented carbide cutter with coating NC Mill G9F42120N 4F. Tools made of high-speed steel should not be used for machining polymer concrete, as they exhibited the highest intensity of tool wear. The rapid loss of machinability of these tools leads to a rapid increase in cutting force and the roughness of the machined surface. From an economic point of view, cemented carbide end mill cutters with coatings seem to be the appropriate choice for machining polymer concrete.

1 January 2018 in Eksploatacja i Niezawodność – Maintenance and Reliability
Verified
Journal Article
Closed access
NKNorbert Kępczak
Norbert Kępczak
RRRadosław Rosik
Radosław Rosik
WPWitold Pawlowski
Witold Pawlowski
MSMałgorzata Sikora
Małgorzata Sikora
BWBłażej Witkowski
Błażej Witkowski
WSWojciech Stachurski
Wojciech Stachurski

5 January 2025 in Materials
Verified
Journal Article
Open access
PDF file
KSKarolina Patrycja Szadkowska
Karolina Patrycja Szadkowska
NKNorbert Kępczak
Norbert Kępczak
WSWojciech Stachurski
Wojciech Stachurski
WPWitold Pawlowski
Witold Pawlowski
RRRadosław Rosik
Radosław Rosik
JSJakub Sikorski
Jakub Sikorski
The aim of the work was to investigate the influence of the machining parameters on the surface roughness and tool wear during slot milling of a polyurethane block (PUB). In the experiment, the influence of the cutting speed, the feed per tooth and the depth of cut on the roughness Ra and Rz of the milling slot surface and wear of the end mill was analyzed. A three-axis CNC milling machine Emco Concept Mill 55 was used to perform the study. After the machining, the values of parameters Ra and Rz were measured using the Hommel Tester T500 induction profilometer. Three polyurethane materials of different densities were considered: the Labelite 45, the Prolab 65 and the LAB 1000. The wear of the end mill was also examined for each of the tested materials by a workshop microscope. In conclusion, it was indicated how and to what extent the variation in the machining parameters affects the surface geometrical structure of a polyurethane plate. Moreover, the research results for the tested materials were compared with each other.

1 August 2019 in Archives of Materials Science and Engineering
Verified
Journal Article
Closed access
RRR. Rosik
R. Rosik
NKNorbert Kępczak
Norbert Kępczak
MSMałgorzata Sikora
Małgorzata Sikora
BWB. Witkowski
B. Witkowski
RWR. Wójcik
R. Wójcik
SMS. Midera
S. Midera
Purpose: The purpose of this article is discussing the methods of determining the surface roughness of the Ti-6Al-4V ELI titanium alloy obtained after longitudinal turning. The method of determining the mathematical model used for determining the Rz roughness parameter and then the results obtained were compared with values measured and calculated on the basis of equations available in the literature. Design/methodology/approach: The mathematical model in the form of multiple regression function of exponential polynomial was determined using the algorithm of the acceptance and rejection method. The data for calculations was obtained by measuring the surface roughness after turning with different machining parameter values. Findings: A mathematical model was elaborated in the form of a multiple regression function, enabling calculation of the Rz parameter describing the Ti-6Al-4V ELI titanium alloy surface roughness after longitudinal turning. The verification of the dependence obtained confirmed its accuracy. Research limitations/implications: Further research should encompass other values of machining plate geometry, as well as other types of cooling and lubricating fluids and method of applying them. Practical implications: The mathematical model can be helpful when choosing the conditions in which the turning process will be carried out. It also constitutes a basis for further optimisation of that process. Originality/value: The results of this research are a novelty on a worldwide scale. No research of this type has been conducted with regard to analyses and optimisation of longitudinal turning of the Ti-6Al-4V ELI titanium alloy.